| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 1 |
| What is the regional telco office called, where the customers
local loop terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| The following selections show the command prompt and the
configuration of the IP network mask. Which two are
correct?
A. Router#term IP netmask-format { bitcount | decimal |
hexadecimal }
B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }
C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }
D. Router#ip netmask-format { bitcount | decimal | hexadecimal } | | 1 |
| What is the protocol number for TCP?
A.) 80
B.) 21
C.) 11
D.) 6 | | 1 |
| What does a router do with a packet that it does not have a
destination network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 1 |
| When you issue the command show version your router returns
"Configuration register is 0x0101" From where does the
router boot?
A. ROM
B. NVRAM
C. Flash
D. a TFTP server | | 1 |
| What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner # | | 1 |
| What does CCNA stand for?
A. Cisco Certified Network Administrator
B. Cisco Certified Network Associate
C. Certified Circuitry in Networking Apprentice
D. Calico Cats of North America | | 2 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| Your network is having IP problems connecting to one or more
Frame Relay peer routers. Which two commmands should you
use to show the routers that are reachable? (Choose two)
A. show ip map
B. show ip router
C. show frame-relay map
D. debug frame-relay map | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Rotuer(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| Given the following IP address from the Class C address
range 192.168.21.12. Your network plan needs addresses for
28 small prkps Each office uses its own shored. The
network design specifies that you confound for five bits of
subnetting. When you confound for this in Cisco IOS
software which shored mask should you use?
A. 255.255.0.28
B. 255.255.255.0
C. 255.255.255.28
D. 255.255.255.248
E. 255.255.255.252 | | 1 |
| Which layer is responsible for providing mechanisms for
multiplexing upper-layer application, session establishment,
and tear
down of virtual circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| A user device that connects to a DCE must be which of the
following?
A.) DTE
B.) CPE
C.) Demarc
D.) DCE
E.) CO | | 1 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 1 |
| What is an example of a valid MAC address?
A. 192.201.63.251
B. 19-22-01-63-25
C. 0000.1234.FEGA
D. 00.00.12.34.FE.AA | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
