MIDI and MPEG are examples of what layer of the OSI seven layer

model?

A.) Session

B.) Network

C.) Datalink

D.) Transport

E.) Application

F.) Presentation

Answers were Sorted based on User's Feedback



MIDI and MPEG are examples of what layer of the OSI seven layer model? A.) Session B.) Netw..

Answer / guest

Answer: F

Is This Answer Correct ?    10 Yes 1 No

MIDI and MPEG are examples of what layer of the OSI seven layer model? A.) Session B.) Netw..

Answer / janarthanan

datalink layer

Is This Answer Correct ?    2 Yes 1 No

MIDI and MPEG are examples of what layer of the OSI seven layer model? A.) Session B.) Netw..

Answer / assas

Application Layer

Is This Answer Correct ?    0 Yes 2 No

Post New Answer

More CCNA Interview Questions

Which statement about Ethernet networks is true? A. The advantage of a full duplex is the ability to transmit data over 111 cable B. Full duplex Ethernet requires a point-to-point connection when only two nodes are present C. Ethernet switches can use full duplex mode to connect multiple nodes to a single pod of a switch D. Half duplex is a cut through packet processing method that is vow fast little error correction Full duplex is a store and forward method that is slower but has better error correction

1 Answers  


Which command would show all Ethernet interfaces with IPX configured on them? A.) show interface ipx ethernet B.) show ipx interface C.) show ipx interface ethernet D.) show ipx E.) show version F.) show run

1 Answers  


In regards to the ISDN BRI standard, which channel is used for control? A.) B B.) D C.) E D.) I E.) Q

2 Answers  


The command 'debug ip rip' will do which of the following? A.) Show Neighbor Info. B.) Display RIP routing updates. C.) Show routing table changes. D.) Show all IP traffic. E.) This is not a valid router command. F.) Cause the router to respond with 'Ambiguous command'

1 Answers  


Identify 3 IP applications? A.) AURP B.) ARP C.) Telnet D.) SMTP E.) DNS F.) RARP

2 Answers  






When we use interface mode?

0 Answers  


Hi, All I am configuring EIGRP in Packet tracer, after configuring all the things it is not working but in one condition it is working fine if i am putting all my router and network withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but whenever i am puting different network subnets e.g. in one network it is RA(config-if)#=ip address 10.0.0.1, and in fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in third router RC(config-if)#=ip address 11.0.0.2 and in fa 0/0 172.16.1.10 and after configuring all this serial is showing up and protocol showing up but eigrp process not taking place after adding eigrp configuration, i tried with "no auto-summary" command but not working.. Suggest me where i missing something? can mail me at : gtech.innovator@gmail.com

20 Answers  


Which layer is responsible for framing? A.) Application B.) Data Link C.) Physical D.) Network E.) Transport

3 Answers  


If configuring a Cisco router to connect to a non-Cisco router across a Frame Relay network, which encapsulation type would you select? A.) Q933a B.) ISDN C.) IETF D.) CISCO E.) ANSI

1 Answers  


What is the default size of frame?

0 Answers  


what is the subnet for the host ip address 172.16.210.0/22

8 Answers   IBM, Microland,


Which of the following provide correct information about a protocol at the transport layer of the OSI model? A.) UDP - Provides Connectionless datagrams service B.) TCP - Provides Connection Oriented Services C.) SMTP - Provides Mail Exchange D.) IP - Route determination E.) TCP - Provides Flow Control and Error Checking F.) FTP - Transfers of Files

2 Answers  


Categories