| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Which of the following are examples of the Transport Layer?
A.) SQL
B.) UDP
C.) IP
D.) LLC
E.) ARP | | 1 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| What is the purpose and default value of the CDP timer command?
A.) 90 seconds; interval before an entry expires
B.) 60 seconds; interval between updates
C.) 60 seconds; interval before an entry expires
D.) 90 seconds; interval between updates | | 1 |
| What is the difference between TCP and UDP?
A.) TCP is connection-oriented; UDP uses acknowledgements only
B.) TCP is connection-oriented; UDP is connectionless
C.) Both TCP and UDP are connection-oriented, but only TCP
uses windowing
D.) TCP and UDP both have sequencing, but UDP is connectionless | | 2 |
| what is the difference between dynamic NAT and NAT
overload ? and how it works ?
| | 4 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 1 |
| Given an IP host address of 172.16.2.160 and a shored mask
of 255.255.255.192 to which shored does the host belong?
A. 172.16.2.32
B. 172.16.2.64
C. 172.16.2.96
D. 172.16.2.128
E. 172.16.2.192 | | 2 |
| You have an IP host address of 201.222.5.121 and a subnet
mask of 255.255.255.248. What is the broadcast address?
A. 201.222.5.127
B. 201.222.5.120
C. 201.222.5.121
D. 201.222.5.122 | | 1 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 1 |
| Which port numbers are used by TCP and UDP to set up
sessions with
other
hosts?
A.) 1024 and above
B.) 6 and 17 respectively
C.) 1-25
D.) 6-17 | | 4 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| Which term describes the process in which frames from one
network system are placed inside the frames of another
network system?
A. bridging
B. tunnelling
C. data link control
D. generic routing
E. packet switching | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 3 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | | 1 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
