| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Which is not a common problem with Distance-Vector routing?
A.) Slow convergence.
B.) Complex configuration.
C.) Routing loops.
D.) Periodic updates can slow convergence.
E.) Counting to infinity. | | 1 |
| What are the OSPF router rules???? | NIIT | 6 |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | CMS | 2 |
| Can anyone explain the Split Horizon rule in RIP & also
Split Horizon with Poison reverse.
Jitu.... U knw wat i expect.. hehehehehe... | | 1 |
| Which layer defines the physical topology?
A.) Application
B.) Transport
C.) Network
D.) Data Link
E.) Physical
F.) Session | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | | 2 |
| Identify the correct pair of Novell Ethernet encapsulation and
Cisco terminology?
A.) Ethernet II, Snap
B.) Ethernet 802.3, Novell-Ether
C.) Ethernet SNAP, Arpa
D.) Ethernet 802.2, Snap | | 1 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| Which three of the following are true statements about
connection-oriented
sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged are retransmitted by the
receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 3 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 1 |
| When a Distance Vector routing protocol detects that a connected
network has gone down, it sends out a special routing update
packet,
telling all directly connected routers that the distance to
the dead
network is infinity. This is an example of which routing
technology?
A.) ICMP.
B.) Only Link State routing protocols have this intelligence.
C.) Triggered updates.
D.) Garrison-4.
E.) Split Horizon.
F.) Poison Reverse. | | 1 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
mac-address 0005.1b00.5b58 | | 4 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Identify the 3 major functions at layer 3 of the OSI model?
A.) Forwarding process
B.) Logical addressing
C.) End-to-end connnections
D.) Path selection
E.) MAC address examination
F.) Network monitoring | | 2 |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| What type of switching creates variable latency through the
switch?
A.) Cut-Through
B.) Inverted
C.) Layer 4
D.) Multiplexed
E.) Store and Forward | | 1 |
| Which layer of the 7 layer model is responsible for representing
the application information between 2 different OS's? For
example,
converting ASCII to EBCIDIC.
A.) Transport
B.) Application
C.) Physical
D.) Session
E.) Presentation
F.) Network | | 2 |
| Station A is transmitting data to station B faster that
station B
can handle it. When station B's buffer fills up, it send out
a message
to station A to stop sending data. After B empties out its
buffer,
station B sends a message to station A to start sending data
again.
This is most directly an example of (pick the best answer only):
A.) Poison Reverse
B.) Connectionless protocol
C.) Windowing
D.) Connection oriented protocol
E.) Flow Control
F.) Split Horizon | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
