| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following is true regarding standard ISDN BRI
service?
A.) ISDN BRI B channels are typically 64K.
B.) ISDN BRI can handle only voice.
C.) ISDN BRI can handle only data.
D.) ISDN BRI has 2B and 1D channels.
E.) ISDN BRI D channels are 16K.
F.) ISDN BRI can handle voice and data. | | 1 |
| When you use the Cisco IOS command show configuration on a
router which part of the output shows the specific conferred
IP addresses and shored masks?
A. the IP host table
B. the interfaces output
C. each section of the output
D. the global configuration statements
E. the section under the autonomous system number | | 1 |
| What is the Function of Router? | | 3 |
| What is the Network Layer of the OSI responsible for?
A.) Bridging
B.) Routing packets through an internetwork
C.) Regenerating the digital signal
D.) Gateway services | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 1 |
| What is difference between Store-and-Forward, cut-through,
Fragment-Free Method? | Microsoft | 2 |
| Which statement is true regarding Administrative distance?
A.) It is a metric
B.) Number of hops between two routers
C.) Trustworthiness of the routing information
D.) RIP Administrative distance is 100 | | 1 |
| Which statement about switched and routed data flows is correct?
A. Switches create a single collision domain and a single
broadcast domain. Routers provide separate collision domains
B. Switches create separate collision domains but a single
broadcast domain. Routers provide a separate broadcast domain
C. Switches create a single collision domain and separate
broadcast domains. Routers provide a separate broadcast
domain as well
D. Switches create separate collision domains and separate
broadcast domains. Routers provide separate collision domains | | 1 |
| Which switching technology can reduce the size of a
broadcast domain?
A.) Cut-Through
B.) Store-and-Forward
C.) Spanning Tree Protocol
D.) RARP
E.) ARP
F.) VLAN | | 1 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| Which command can verify only Network layer connectivity
between 2
hosts?
A.) ping
B.) e-mail
C.) plp
D.) arp
E.) telnet | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| Which command enables directly connected network 199.55.72.0
to be used by RIP?
A. Router(config router)# rip 199.55.0.0
B. Router(config router)# rip 199.55.72.0
C. Router(config router)# network 199.55.0.0
D. Router(config router)# network 199.55.72.0 | | 1 |
| Identify 3 methods not used to prevent routing loops?
A.) Holddown timers
B.) Sequence numbers
C.) Triggered updates
D.) Split horizon
E.) Area hierarchies
F.) Order of router startup | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physical
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 1 |
| Which of the following are examples of the Session Layer?
A.) IP
B.) Netbios Names
C.) NFS
D.) Token Ring
E.) SQL
F.) RPC | | 1 |
| Which three commands are used to configure information into
RAM on a router? (Choose three)
A. configure memory
B. configure terminal
C. configure overwrite
D. copy tftp startup-config
E. copy running-config startup-config
F. copy startup-config running-config | HCL | 5 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| What is Cisco register bits? How they help? | jetking | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
