| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the purpose of ICMP?
A.) Avoiding routing loops
B.) Send error and control messages
C.) Transporting routing updates
D.) Collision detection | Hughes | 2 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 3 |
| Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)#router igrp 100
Router(config-router)#network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0 | | 2 |
| Which of the following are ways to provide login access to a
router?
A.) HTTP
B.) Console
C.) Telnet
D.) Aux Port
E.) SNMP
F.) LLC | | 1 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 2 |
| Identify the switching method that examines the destination MAC
address as the frame is being received then begins
forwarding the frame
prior to receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| in the ospf area network dr and bdr selection procedure occur
let there are 4 router in that n/w r1 have the higher priority
then r2 and r2 have higher priority then r3 and so on
like that
r1>r2>r3>r4
now as we know that selection of dr and bdr based upon the
router priority so in this case r1 will be dr and r2 will be
bdr
now my question is that if i am going to implement 5th
router which have greater priority then r1 then will it become dr atomically
remember that i am not going change my 5 or 1st router property
answer that one please | | 2 |
| What is the Broadcast MAC Address? | Avaya | 2 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Identify the command to view the configuration-register value?
A.) show register
B.) display config-register
C.) show config
D.) show version | | 1 |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| thnx jitender...its me shridh...m working for SG ltd..the
situation iz like ths -at a specific time in our company the
internet connectivity goes off...v hav two networks in our
company...but out of it only one link goes down for 5-10
sec...a fastethernet port becomes down for few sec and
automatically becomes Up... Is this occures becoz of Power??
If yes thn y the 2nd network is not affected??
plz tel me jitender how to resolve ths problem?
as u sd loop in switch is the primary cause of ths....i
wanna know how to resolve it...thnx for ur replys jitender
sinha. | | 2 |
| What is a disadvantage of using a connection oriented
protocal such as TCP?
A. Packet acknowledgement may add overhead
B. packets are not tagged with sequence numbers
C. Loss or duplication of data packets is more likely to occur
D. The application layer must assume responsibility for
correct searchers of the data packets | | 1 |
| At which layer of the OSI Reference Model do bridges operate?
A.) Physcial
B.) Session
C.) Datalink
D.) Transport
E.) Network | | 2 |
| Which two steps are part of the process of creating Frame
Relay subinterfaces on a point to point connection? (Choose
two)
A. configure the router to forward all broadcast packets
B. remove any network address assigned to the physical interface
C. configure the local data link connection identifier
(DICI) for the subinterfaces
D. cartoon the total committed information rate (CIP)
available among the subinterfaces | | 1 |
| Tell me CCNA Course + Dump Q/A in chennai? | Wipro | 1 |
| IP extended access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) all of the above
C.) protocol
D.) source address
E.) port | | 1 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| Which command can verify Application Layer connectivity
between 2
hosts?
A.) ftp
B.) snmp
C.) telnet
D.) ping
E.) traceroute | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
