How does a switch use store and forward? A.) By using a Class I repeater

Advertise your Business Here

Refer this Site

Login | Sign Up


	Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff HERE

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

How does a switch use store and forward?

A.) By using a Class I repeater in a collision domain

B.) The LAN switch copies the entire frame into its onboard
buffers and

then looks up the destination address in its forwarding, or
switching,

table and determines the outgoing interface

C.) By using broadcast addresses as source addresses

D.) The switch waits only for the header to be received
before it checks

the destination address and starts forwarding the packets

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets

Answer
# 1

Answer: D

Is This Answer Correct ?

0 Yes

1 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


b Which protocol for PPP LCP (Link Control Protocol) performs a challenge handshake? A. CHAP B. PAP C. UDP D. IPX		1
Which two steps are part of the process of creating Frame Relay subinterfaces on a point to point connection? (Choose two) A. configure the router to forward all broadcast packets B. remove any network address assigned to the physical interface C. configure the local data link connection identifier (DICI) for the subinterfaces D. cartoon the total committed information rate (CIP) available among the subinterfaces		1
What does the following line for an access list do? 'access-list 101 deny tcp 3.4.5.0 0.0.0.255 any eq 23' A.) deny all ftp traffic B.) deny all ftp traffic from subnet 3.4.5.0 C.) deny all telnet traffic from subnet 3.4.5.0 D.) deny all ftp traffic to subnet 3.4.5.0 E.) deny all telnet traffic		1
Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table		1
Novell NetWare has an Ethernet frame type called Ethernet_SNAP. What is the matching Cisco command line keyword for this encapsulation method? A.) arpa B.) sap C.) snap D.) gns E.) dix F.) novell-ether		1
Identify the 2 commands that save the running-config to a TFTP server? A.) write running tftp B.) copy running network C.) copy running tftp D.) write network		1
Identify command that configures 'Cisco1' as a secret password? A.) Router(config)# enable secret password Cisco1 B.) Router(config)# enable secret cisco1 C.) Router(config)# enable password Cisco1 D.) Router(config)# enable secret Cisco1		2
What command can be used to test IPX connectivity? A.) Ping 2e.000.0045.8923 B.) Ping 192.168.100.1 C.) Ping ipx 2e.0000.0045.8923 D.) Ipx ping 2e.0000.0045.8923		3
Which OSI layer provides best effort end to end packet delivery? A.) Data-Link B.) Presentation C.) Network D.) Transport E.) Physical F.) Application		1
WHAT IS SERIAL TRANSMISSIONS,PARALLELL TRANSMISSION	ASD-Lab	2
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0		2
Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc		2
Access lists are numbered. Which of the following ranges could be used for an IP access list? A. 600 - 699 B. 100 - 199 C. 1 - 99 D. 800 - 899 E. 1000 - 1099		1
Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1		1
What is the result of segmenting a network with a router into segments 1 and 2? A. It increases the number of collisions B. It decreases the number of broadcast domains C. It connects segment 1 and broadcasts to segment 2 D. It connects segment 1 and broadcasts from genre to segment 2		1
Bridges work at what layer of the OSI model? A.) Data Link B.) Network C.) Physical D.) Application		2
Identify the true statement regarding subnetting? A.) Allows for more host address B.) Borrow bits from the network portion of the address C.) Allows for unlimited number of networks D.) Borrow bits from the host portion of the address		1
HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS PREFERED OVER ANY NETWORK PROTOCOL?	Aricent	2
there is three mode of vtp let there are three switch s1 in server mode s2 in transparent mede and s3 in clint mode then will that tranparnt mode going to effect the network if yes then how and if no then what it will do	IBM	1
255.255.255.128/what is the n/w id ,broadcast id and the number of valid host(according to disco rules)	Reliance	2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com