| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| The network portion of an address typically represents a:
A.) Router
B.) Ethernet MAC address.
C.) Computer
D.) Host
E.) Segment | | 2 |
| What information is provided by the local management
interface (LMI)?
A.) LMI encapsulation type
B.) The current DLCI values
C.) The status of virtual circuits
D.) The global or local significance of the DLCI values | | 1 |
| Identify 3 characteristics of a connection oriented protocol?
A.) Path determination
B.) Flow control
C.) Acknowledgements
D.) Uses hop count as metric
E.) 3 step handshake | | 2 |
| What does the 'S' mean when looking at the routing table?
A.) Statically connected
B.) Directly connected
C.) Dynamically attached
D.) Shutdown route | | 1 |
| what is routing and routed protocol ? | | 7 |
| what is the diffrence betwwen telnet and ssh.this question
is asked by nikhil and i am plasing the answer here insteed
of his personal mail.
| | 4 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | | 1 |
| in the ospf area network dr and bdr selection procedure occur
let there are 4 router in that n/w r1 have the higher priority
then r2 and r2 have higher priority then r3 and so on
like that
r1>r2>r3>r4
now as we know that selection of dr and bdr based upon the
router priority so in this case r1 will be dr and r2 will be
bdr
now my question is that if i am going to implement 5th
router which have greater priority then r1 then will it become dr atomically
remember that i am not going change my 5 or 1st router property
answer that one please | | 2 |
| Which of the following are solutions to the problems encountered
with Distance-Vector routing?
A.) Defining a Maximum
B.) Poison Reverse
C.) Triggered Updates
D.) Shortest path first algorithm.
E.) Split Horizon | | 1 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | ACS | 1 |
| friends i have some problem in the acess list plz help me
out.
purbi sinha.
1 what is the diffrence b/w inbound and out bound access
list
2 what is main diffrence betwwen standred acesslist and
extended access list
3 where should i keep stnadred access list and exatended
access list i mean at which interface and why?
4 why wild card masking is used
5 what is switch febric in switching
plz help me out i am litle bit confuse
| | 1 |
| PICT & JPEG are examples of what layer in the OSI seven
layer model?
A.) Transport
B.) Presentation
C.) Application
D.) Datalink
E.) Network
F.) Session | | 1 |
| what is 5-4-3 rule? | | 1 |
| What is the default routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) Bandwidth and delay
D.) Hop count | | 2 |
| Novell IPX network addresses have two conferrable parts.
The network administrator specifies the IPX network number.
How is the node number determined?
A. It is the serial number of the given device
B. It is assigned as a lease by Novell DHCP
C. It is also set by the network administrator
D. It is usually the MAC address of one Interface
E. It is downloaded by Netware Core Protocol (NCP) | | 1 |
| Given the following output, how can we close Telnet session
2? (Choose two)
CCNA2620#show sessions
Conn Host Address Idle Conn Name
1 131.108.100.152 131.108.100.152 0 131.108.100.152
*2 126.102.57.63 126.102.57.63 0 126.102.57.63
❍ A. Press the Enter key and enter exit.
❍ B. Enter disconnect 2.
❍ C. Press the Enter key and enter disconnect 2.
❍ D. Enter close 2. | | 1 |
| What is the difference between TCP and UDP?
A.) TCP is connection-oriented; UDP uses acknowledgements only
B.) TCP is connection-oriented; UDP is connectionless
C.) Both TCP and UDP are connection-oriented, but only TCP
uses windowing
D.) TCP and UDP both have sequencing, but UDP is connectionless | | 4 |
| What are the two most common transport layer protocols?
UDP
TCP
IPX
ARP
| | 2 |
| Which command-line keywords are valid for choosing
Frame-Relay LMI
types?
A.) itu-t
B.) dlci
C.) ansi
D.) rfc 1544
E.) cisco
F.) q933a | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
