ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
tip   To Refer this Site to Your Friends   Click Here
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
You need to come up with a TCP/IP addressing scheme for your

company. How

many network IDs must you allow for when you define the
subnet mask for

the network?

A.) One for each WAN link

B.) One for each router interface

C.) One for each NIC installed in each client

D.) One for each subnet with hosts

E.) One for each host ID
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: You need to come up with a TCP/IP addressing scheme for your company. How many network IDs must you allow for when you define the subnet mask for the network? A.) One for each WAN link B.) One for each router interface C.) One for each NIC installed in each client D.) One for each subnet with hosts E.) One for each host ID
Answer
# 1
Answer: A D
 
Is This Answer Correct ?    0 Yes 0 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
Which of the following is a layer 2 device? A.) Switch B.) Bridge C.) Repeater D.) Hub  2
Identify the OSI layer which is responsible for end-to-end connections? A.) Network B.) Transport C.) Session D.) Data link E.) TCP  2
Which protocol will let neighbor routers know if your internetwork experienced congestion on a serial port? A.) BootP B.) IP C.) ICMP D.) ARP E.) FTP F.) RARP  2
How do i decide if an extended access-list is in or out?  1
Which commands would assign and enable IPX on an interface ? A.) enable netware B.) enable novell-ether C.) router#(config)ipx routing D.) You must first enable IPX globally and then assign the network number to the interface . E.) enable ipx F.) router#(config-if)ipx network 4a  1
Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc  2
what is native vlan any one explain sooraj  2
Select the correct statements about PPP and SLIP for WAN communications? A. PPP uses its Network Control Programs (NCPs) component to encapsulate multiple protocols. B. PPP can only transport TCP/IP C. SLIP can only transport TCP/IP. D. SLIP uses its Network Control Programs (NCPs) component to encapsulate multiple protocols.  1
Identify the purpose of the wildcard mask? A.) Match a certain portion of the IP address while ignoring the rest of the address B.) Determine the class of the IP address C.) Determine the network portion of an IP address D.) Hide the host portion of an IP address  1
how many pass word you can configure on cisco 2500 router HCL2
Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route  1
Which frame has a Type field to identify the upper-layer protocol? A.) 802.3 B.) 802.2 C.) 802.5 D.) Ethernet_II  1
What 2 commands verify end to end communications? A.) Trace B.) debug ip session C.) Ping D.) Route  2
Identify 2 features of PPP CHAP authentication? A.) Username and password is sent in clear text B.) Authentication messages are sent periodically during the connection C.) Less secure then PAP D.) Local router 'challenges' the remote router  1
Which statement about Ethernet networks is true? A. The advantage of a full duplex is the ability to transmit data over 111 cable B. Full duplex Ethernet requires a point-to-point connection when only two nodes are present C. Ethernet switches can use full duplex mode to connect multiple nodes to a single pod of a switch D. Half duplex is a cut through packet processing method that is vow fast little error correction Full duplex is a store and forward method that is slower but has better error correction  1
You would like to have a notation that when a user issues the command 'show interface serial 0', a line is displayed indicating that, 'This is the connection to Company A.' What interface command would accomplish this? A.) banner motd #This is the connection to Company A.# B.) interface This is the connection to Company A. C.) This cannot be done for an individual interface. D.) description This is the connection to Company A. E.) banner This is the connection to Company A. F.) display This is the connection to Company A.  1
Where is the point between the customers site and the phone carrier that responsibility changes? A.) CO B.) Demarc C.) DCE D.) DTE E.) CPE  1
What is the administrative distance for IGRP? A.) 90 B.) 120 C.) 110 D.) 100  2
What would be the first command from global configuration mode to enable RIP on your router for interface E0, with an address of 181.86.4.4 and mask of 255.255.255.0 ? A.) router rip B.) network 181.89.4.0 255.255.255.0 C.) router rip int e0 D.) router rip 181.86.0.0 E.) router rip 181.86.4.0 F.) network 181.86.0.0  1
Which ISDN protocol prefix specifies switching and signaling? A.) I B.) E C.) Q D.) S  1
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com