| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| what is flow control,. | | 4 |
| What does CCNA stand for?
A. Cisco Certified Network Administrator
B. Cisco Certified Network Associate
C. Certified Circuitry in Networking Apprentice
D. Calico Cats of North America | | 3 |
| What do the following commands accomplish?
access-list 1 deny 172.16.4.0 0.0.0.255
access-list 1 permit any
interface ethernet 0
IP access-group 1 out
A. This will block traffic from subnet 172.16.4.0 and allow
all other
traffic.
B. This will allow traffic from subnet 172.16.4.0 and block
all other
traffic.
C. All traffic is allowed.
D. All traffic is blocked. | | 1 |
| An ISDN BRI circuit can be described as which of the following?
A.) 3B channels
B.) 2-64Kbps B channels and 1-16Kbps D channel
C.) none of the above
D.) 2-64Kbps B channels and 1-16Kbps C channel | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 2 |
| Which technologies listed below help prevent network loops in a
switched (bridged) environment?
A.) Store-and-Forward
B.) IEEE 802.1d
C.) Diikjstra Algorithm
D.) Cut-Through
E.) Spanning Tree Protocol
F.) Routing | | 1 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 1 |
| What is the distance limitation for 100BaseT?
A. 607 ft
B. 25 Meters
C. 1,000 ft
D. 185 Meters | | 1 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| What is the routing metric used by RIP?
A.) Route poisoning
B.) Split horizon
C.) Hop Count
D.) TTL | | 1 |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| what is vc,pvc,lmi and dlsi | | 1 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| You want to enable both arpa and snap encapsulation on one
router interface. How do you do this?
A. The interface can handle multiple encapsulation types
with no extra configuration.
B. Assign two network numbers, one for each encapsulation
type.
C. Enable Novell-ether to run multiple encapsulation types.
D. Both arpa and snap are enabled by default so you don't
have to configure anything. | | 1 |
| What is the difference between RIP & RIPng????
Can anyone explain it..!!!
Thank u in advance. | | 1 |
| Identify the purpose of the Trace command?
A.) Explorer packet transmitting routing information
B.) Test connectivity
C.) Determine the path a packet is taking through the network
D.) Transmits user data when buffers are full | | 1 |
| What is the regional telco office called, where the customers
local loop terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
