| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home.
D. a standard 28.8 analog dialup connection to the user at home. | | 1 |
| Which layer is responsible for identifying and establishing the
availability of the intended communication partner?
A.) Application
B.) Presentation
C.) Transport
D.) Session
E.) Network | | 1 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Which can be true regarding VLANs?
A.) They are created by location
B.) They are created by function
C.) They are created by department
D.) They are created by group | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Router# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| what is routing and routed protocol ? | | 7 |
| What is the function of Layer 2 Switch? | | 1 |
| Select the correct statements about PPP and SLIP for WAN
communications?
A. PPP uses its Network Control Programs (NCPs) component to
encapsulate
multiple protocols.
B. PPP can only transport TCP/IP
C. SLIP can only transport TCP/IP.
D. SLIP uses its Network Control Programs (NCPs) component to
encapsulate multiple protocols. | | 1 |
| Hi Jitendera, I continuously read your answers which is
more knowlegable than books...
Q.I am facing some problems in subnetting.can you plzz
explain the subnetting process.. will be remain thankful | | 3 |
| What is public and private ip address., explain? and also
explain the ip address range of both public and private?
and where we use that public and private ip address? | | 10 |
| You would like to have a notation that when a user issues
the command
'show interface serial 0', a line is displayed indicating
that, 'This is
the connection to Company A.' What interface command would
accomplish this?
A.) banner motd #This is the connection to Company A.#
B.) interface This is the connection to Company A.
C.) This cannot be done for an individual interface.
D.) description This is the connection to Company A.
E.) banner This is the connection to Company A.
F.) display This is the connection to Company A. | | 1 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing
protocol?
A.) Physically connected network(s)
B.) Configure the classfull address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Same autonomous network | | 1 |
| What is the default encapsulation and frame type on an Ethernet
interface when enabling Novell?
A.) SNAP
B.) Ethernet_II
C.) 802.2
D.) 802.3
E.) SAP
F.) Token_SNAP | | 1 |
| What is masking? why is needed? | | 4 |
| Identify the command to display the IP host table?
A.) show ip hostnames
B.) show ip names
C.) show hosts
D.) show ip hosts | | 1 |
| If a frame is received at a switch and only the destination
hardware
address is read before the frame is forwarded, what type of
switching
method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
