| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecing to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecing to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 1 |
| Which layer is responsible for synchronizing sending and
receiving
applications?
A.) Presentation
B.) Session
C.) Transport
D.) Application
E.) Network | | 2 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Which command will display Ethernet 0's IP address?
A.) display ip address e0
B.) show ip interface e0
C.) show address e0
D.) sh ip address e0
E.) show all | | 1 |
| router | Infotech | 1 |
| Identify the 3 key features of the Cisco Discovery Protocol?
A.) Off by default
B.) Will allow for the discovery of layer 3 addresses on
neighbor routers
C.) Verify connectivity
D.) Open standard
E.) Does not require any layer 3 protocols to be configured | | 1 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 2 |
| thnx Jitender singh...as u told to install a stp in switches
and problem vil b get solved...i wanna kno how to install
stp in switches??
plz tel me detailled steps...
thanx for ur answer. | | 1 |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| hi friends i have some problem regarding technical round
ahr round plz tell me what should the right answer
technical questions
1 what is brouter
2 what is the menaing of 10 base2, 10 base 5 and 10baset
3 what is diffrence between bit rate and baud rate.
and this question was tooooooooooo much difficult to me
that
hr said to me that
rank me after the taking the all short of interview | | 5 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 2 |
| What are hold-downs used for?
A.) To prevent regular update messages from reinstating a
route that has
come back up
B.) Information received on an interface cannot be sent back
out the same
interface
C.) To prevent regular update messages from reinstating a
route that has
gone down
D.) To hold the routing table from being sent to another router | | 1 |
| If a frame is received at a switch and only the destination
hardware address is read before the frame is forwarded, what
type of
switching method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| What are the three phases of PPP session establishment?
A. Link establishment phase
B. Authentication phase
C. Network layer protocol phase
D. Handshake phase
E. Dial-in phase | | 2 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| Which layer of the 7 layer model provides services to the
Application layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation | | 1 |
| As the system administrator, you enter the following commands at
the command prompt:
ipx routing
access-list 800 permit 2b 4d
int e0
ipx network 4d
ipx access-group 800 out
int e1
ipx network 2b
int e2
ipx network 3c
What did these command accomplish?
A. Traffic from network 4c destined for network 4d will be
forwarded out
Ethernet0.
B. Traffic from network 3c destined for network 4d will be
forwarded out
Ethernet0.
C. Traffic from network 2b destined for network 4d will be
forwarded out
Ethernet0.
D. Traffic from network 4d destined for network 2d will be
forwarded out
Ethernet0. | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
