| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is the need og
jitu(config)#ip helper address <ip address>
can any one exaplain it briefly
specially shain i am looking towards you.Becoz you are the
only one who can solve my that problem not even jitendera sinha | | 3 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| What is the default IPX Ethernet encapsulation?
A.) SNAP
B.) Arpa
C.) 802.2
D.) Novell-Ether
E.) SAP | | 2 |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | | 3 |
| Identify the command mode necessary to enter the standard ping
command?
A.) Router(config)#
B.) Router>
C.) Router(std-ping)#
D.) Router(config-if)# | | 2 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 2 |
| Identify the default IPX serial encapsulation?
A.) Novell-Ether
B.) SDLC
C.) SNAP
D.) HDLC | | 1 |
| Which can be true regarding VLANs?
A.) They are created by location
B.) They are created by function
C.) They are created by department
D.) They are created by group | | 1 |
| Which three statements about common elements of the TCP/IP
protocol stack are true? (Choose three)
A. IP provides connectionless service and routing capabilities
B. APP enables devices to locate the IP address of local devices
C. UDP provides simple connectionless service without
windowing or acknowledgments
D. ICMP provides connection oriented management data to
routers and Layer 3 switches
E. TCP enables devices to send large quantities of data
using windowing in a connection oriented manner | | 2 |
| What is VLSM? Why we Create? When we Create? Implement VLSM
with example? | | 4 |
| What is the protocol number for TCP?
A.) 80
B.) 21
C.) 11
D.) 6 | | 1 |
| Which command will enable debugging for IPX RIP updates?
A.) debug ipx
B.) debug ipx rip
C.) debug ipx rip activity
D.) debug rip
E.) debug ipx packets | | 1 |
| How do you view the routers current processor utilization?
A.) show version
B.) show processes cpu
C.) show running-config
D.) show startup-config
E.) show cpu
F.) show utilization | Cisco | 2 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| The following commands were entered at the command prompt of a
Cisco router. What do they accomplish?
access-list 1000 deny 9e.1234.5678.1212 4
access-list 1000 permit -1
interface ethernet 0
ipx network 9e
interface ethernet 1
ipx network 4a
interface serial 0
ipx network 1
ipx output-sap-filter 1000
A. File server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0.
B. All other SAP services, other than file server, from any
source will
be forwarded on S0.
C. All other SAP services, other than print server, from any
source will
be forwarded on S0.
D. Print server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0. | | 1 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of
the connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| What is Cisco's default encapsulation method on serial
interfaces?
A.) ANSI
B.) Cisco
C.) Q933a
D.) HDLC | | 2 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
