| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which port numbers are used by TCP and UDP to set up
sessions with
other hosts?
A.) 1024 and above
B.) 6 and 17 respectively
C.) 1-25
D.) 6-17 | | 2 |
| What is the first step in data encapsulation?
A.) User information is converted into data.
B.) Frames are put into bits.
C.) Data is converted into segments.
D.) Segments are converted into datagrams and packets.
E.) Packets are put into logical frame. | | 1 |
| To prevent Service Advertisements (SAPs) from flooding a
network, Cisco routers do not forward them. How are
services advertised to other networks?
A. Each router builds its own SAP table and forwards that
every 60 seconds.
B. Each router assigns a service number and broadcasts
that.
C. SAPs aren't necessary with Cisco routers.
D. Cisco routers filter out all SAPs. | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| Identify 2 functions of IPX access-lists?
A.) Control SAP traffic
B.) Limit number of Novell servers on a network
C.) Limit number of workstations on a network
D.) Block IPX traffic | | 1 |
| Given the IPX address 4a.0002.1111.a999, what is the network ID
and what is the node ID?
A.) net 4a host 0002.1111.a999
B.) net a999 node 0002.1111
C.) net 0002.1111.a999 node 4a
D.) net 0002.1111 node a999 | | 1 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| what is difference between
1 pap and chap(quite easy but need on line answer)
2 chap and ms-chap(plz describe briefly)
now i have posted the question is there any one to help me?
| | 1 |
| Which command will display adjacent routers found by the Cisco
Discovery Protocol?
A.) show all
B.) show cdp entry
C.) show ip neighbors
D.) show cdp neighbor detail
E.) show cdp neighbor
F.) show neighbor | | 1 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| let there are three switch and there are 3 ree valn craed
on each switch that is vlan 2 on first switch valn 3 on 2nd
switch and vlan 4 is cretaed on switch 3
i have implemnted intervlan routin through ciso switchses.
the router is conected through its fa0/1 port by one switch
and and the two switch are trunked with each other
now question is that we want to comuniacte betwwen vlan but
does alse want that only vlan 2 is allow to access internet
(ISP)which is conected through s0 interface of router.and
no any vlan can access that internet.what should be
solution. | | 1 |
| When editing a line in the CLI mode, what does 'CTRL-A' do?
A.) Moves you to the previous command.
B.) Moves you to the next word.
C.) Moves you to the end of the line.
D.) Moves you to the next command.
E.) Moves you to the beginning of the line. | | 1 |
| What does a router do with a packet that it does not have a
destination network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 2 |
| What is the Between Normal Switch and Manageable Switch? | | 11 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 3 |
| what is the difference between a passive and active hub??
which is better ?? | | 5 |
| What does the 'S' mean when looking at the routing table?
A.) Statically connected
B.) Directly connected
C.) Dynamically attached
D.) Shutdown route | | 1 |
| IGRP uses flash updates, poison reverse updates, holddown
times, and split horizon. How often does it broadcast its
routing table updates?
A. 90 seconds
B. 10 seconds
C. 30 seconds
D. 45 seconds | | 1 |
| |
| For more CCNA Interview Questions Click Here |