| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| When determining whether or not to route a LAN segment,
which rule
of thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| What is an advantage of local area network (LAN) segmentation?
A. smaller collision domains
B. elimination of broadcasts
C. decreased cost of implementation
D. larger number of users within the same domain | | 1 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Which two physical interfaces support PPP? (Choose two)
A. Ethernet
B. Token Ring
C. Synchronous serial
D. Asynchronous serial | | 1 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Which command do you use to set the Secret password to
'roundwood'?
A.) enable login roundwood
B.) enable password roundwood
C.) enable privilege roundwood
D.) enable secret= roundwood
E.) enable secret login roundwood
F.) enable secret roundwood | | 1 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| Identify 3 methods not used to prevent routing loops?
A.) Holddown timers
B.) Sequence numbers
C.) Triggered updates
D.) Split horizon
E.) Area hierarchies
F.) Order of router startup | IIHT | 3 |
| Repeaters work at which layer of the OSI model?
A.) Network
B.) Session
C.) Transport
D.) Physical | Wipro | 3 |
| Identify IPX GNS and it's purpose?
A.) Go Network Server - sends a print job to a network server
B.) Get Nearest Server - locate the nearest server
C.) Guaranteed Network Services - allocates resources to users
D.) Get Notes Server - locates Domino Server | | 1 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home.
D. a standard 28.8 analog dialup connection to the user at home. | | 1 |
| What is the standard ISDN term for a native ISDN modem?
A.) ET
B.) LE
C.) TE2
D.) TE3
E.) TA | | 1 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| What does the 'S' mean when looking at the routing table?
A.) Statically connected
B.) Directly connected
C.) Dynamically attached
D.) Shutdown route | | 1 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 1 |
| Suppose we have 4 switches runing in VTP mode. So when i
create a VLAN in Server Switch this VLAN info reflect in all
other switch. So question is -
A) Suppose i m practicing this scenario in BOSON software,
When a create a VLAN in server switch n ADD ports of switch
to that VLAN, the same number of ports of client switch also
belongs to dat VLAN.
For example - In switch A (Server mode), i create a VLAN 7
name Hyderabad & port number 1, 2 & 3 put into this VLAN.
Another Switch B (Client mode), its also showing that port
number 1,2 & 3 belong the same VLAN.
How cud it possible... As we know, VTP share only VLAN
configuration information. Cud anyone explain it please....!!!!
B)Same thing, when i m practicing in PACKET TRACER 5.0, its
only showing that VLAN configuration information is shared.
No port information is shared at all. I can manually
configure individual switch port to respective VLAN as our wish.
Cud anyone explain it please..!!!
| | 3 |
| What is the administrative distance for IGRP?
A.) 90
B.) 120
C.) 110
D.) 100 | | 3 |
| what is frame relay? | | 8 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
