| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| If configuring a Cisco router to connect to a non-Cisco router
across a Frame Relay network, which encapsulation type would
you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| tell me our traditional ip routing is what
A--conectless
b----conection orented
c-----pacekt switching
d------ckt switching
slect any two
this is the question which i forgot to incoprate
next-questions
| | 3 |
| Identify the hardware component used to store buffers, tables,
running-configuration etc?
A.) NVRAM
B.) ROM
C.) RAM
D.) Flash | | 3 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| how we can creat VPN..??? how it can be configured on cisco
switches..??? can we creat VPN on different networks..???
why we need to create VPN..??? kindly write complete
activity of commands to configure a VPN on switch..??? me
specially looking towards Jatendra and Shahin | | 1 |
| Identify the command that displays the SAP table?
A.) show ipx servers
B.) display SAP table
C.) display SAP's
D.) show sap table | | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 2 |
| What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP
& OSPF??
Can any one explain..!!! | | 4 |
| The CSMA/CD Ethernet IEEE committee is defines as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| how many pass word you can configure on cisco 2500 router | HCL | 2 |
| Which of the following is an example of the Physical Layer?
A.) TCP
B.) ARP
C.) IP
D.) FDDI
E.) LLC
F.) Fast Ethernet | | 2 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 1 |
| Which statement is true when a broadcast is sent in an
Ethernet/802.3 ITAN?
A. The ip shored used is 255.255.255.0
B. The IP address used is 255.255.255.255
C. The MAC address used is 00 00 00 00 00 00
D. The MAC address used is FF FF FF FF FF FF | | 1 |
| Given the configuration example<HR>
<B>interface ethernet0
ipx network 4a
ipx access group 800 out
interface ethernet1
ipx network 3d
interface ethernet2
ipx network 5c
access list 800 permit 3d 4a</B><HR>
Which two actions result from implementing this
configuration? (Choose two)
A. IPX network 5c will not receive any traffic
B. Traffic from network 3d for network 4a will be forwarded
out e0
C. Traffic from network 4a for network 3d will be forwarded
out e0
D. Traffic from network 3d destined for network 4a will be
forwarded out e2
E. The access list is applied to an outgoing interface and
filters outbound traffic | | 1 |
| When configuring the subnet mask for an IP address, which
formats can be used?A. dotted-decimal.
B. Hexadecimal
C. Bit-count
D. Octal
E. Binary | | 1 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Which is not a common problem with Distance-Vector routing?
A.) Slow convergence.
B.) Complex configuration.
C.) Routing loops.
D.) Periodic updates can slow convergence.
E.) Counting to infinity. | | 1 |
| can we measure how much a host exact bandwidth using by a
network cable which is communicating over the network?
options: 1- via Router 2- Switch, 3- other device... if
yes.. then how ( with every option) | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
