| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| You can access three forms of WAN services with Cisco routers.
Select the three forms:
A. Switched or relayed services
B. Interface front end to IBM enterprise data center computers
C. Using protocols that connect peer-to-peer devices like
HDLC or PPP
encapsulation.
D. IPX/SPX
E. NetBEUI | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 3 |
| Although Cisco IOS 11.2 and later can auto-detect the LMI
type in
Frame Relay, which command will force the LMI type to q933a?
A.) frame-relay lmi-type q933a
B.) encapsulation frame-relay q933a
C.) don't need to, it is the default
D.) encapsulation q933a
E.) encapsulation frame-relay type=q933a | | 1 |
| Identify 3 ways in which a router can be configured?
A.) TFTP
B.) Nvram
C.) ROM
D.) Console
E.) Trace | | 1 |
| What is the Difference between Switch and Bridge? | | 3 |
| What was the key reason the International Organization for
Standardization released the OSI model?
A. users could access network servers faster
B. different vendor networks could work with each other
C. the industry could create a standard for how computers work
D. network administrators could increase the overall speed
of their network | | 1 |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | | 2 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)#router igrp 100
Router(config-router)#network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0 | | 2 |
| Which two protocol tools use ICMP? (Choose two)
A. ping
B. telnet
C. configure
D. traceroute
E. show commands
F. standard access lists | | 3 |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| What not a name of an ISP?
A. MSN
B. Comcast
C. Verizon
D. McDonalds | | 1 |
| Which protocol for PPP provides load balancing across
multiple links?
A. Multilink Protocol (MP)
B. Quality
C. Magic Number
D. Stacker
E. Predictor | | 1 |
| How does a switch use store and forward?
A.) By using a Class I repeater in a collision domain
B.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
C.) By using broadcast addresses as source addresses
D.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 2 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| What are 3 ways to provide login access to router?
A.) Console
B.) TFTP
C.) Rlogin
D.) Auxiliary Port
E.) X Windows
F.) Telnet | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
