| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which type of Ethernet framing is used for TCP/IP and
AppleTalk?
A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP | Wipro | 1 |
| Which three types of connectors are commonly associated
with Cisco's V.35 serial cables? (Choose three.)
0 RJ 11
1 DB 60
2 Winchester 15 pin
3 DB 9
4 smart serial
5 RJ 45
| | 3 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| On Cisco catalyst 5000 how would you set the second port on the
controller in the first slot to full duplex?
A.) Set port duplex 1/1 full
B.) Set port duplex 1/2 full
C.) Set port duplex 0/1 full
D.) Set port duplex 0/2 full | | 1 |
| Which of the following would not be displayed by the command
?sho cdp
neighbor detail??
A.) The incoming/outgoing interface.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| Which statement about switched and routed data flows is correct?
A. Switches create a single collision domain and a single
broadcast domain. Routers provide separate collision domains
B. Switches create separate collision domains but a single
broadcast domain. Routers provide a separate broadcast domain
C. Switches create a single collision domain and separate
broadcast domains. Routers provide a separate broadcast
domain as well
D. Switches create separate collision domains and separate
broadcast domains. Routers provide separate collision domains | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 2 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The
LLC establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The LLC
establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| Which statement is true?
A. While bridges are used to segment networks, they will not
isolate broadcast or multicast packets.
B. A bridge looks at every packet within its network segment
and works like a hub re-broadcasting the packet if the
destination is within its network segment.
C. A bridge maintains a table of the IP addresses of the
hosts within its network segment and forwards the packet
directly to the destination based upon the IP address.
D. A bridge resets the hop count by keeping all packets
within the network segment. Only packets addressed to a
specific destination host outside the network segment are
allowed to pass through the bridge. | | 1 |
| what is the high order bit in class a
1
11
110
10
mine answer 1 | | 2 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 2 |
| what is the difference between hdlc and ppp protocol | ASD-Lab | 4 |
| Which OSI layer establishes, maintains and terminates sessions
between
applications?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| You are conferring a Frame Relay router with subinterfaces
on interface Serial 0 Which subinterfaces numbers could you
use for this configuration?
A. 1 and 2
B. 0 2 and 0 3
C. 1 0 and 1 1
D. 0 1 a and 0 1 | | 1 |
| Which two statements about the store and forward switching
method are true? (Choose two)
A. Latency remains constant regardless of frame size.
B. Latency through the switch varies with frame length.
C. The switch receives the complete frame before forwarding it.
D. The switch checks the destination address as soon as it
receives the header and begins forwarding the fram immediately. | | 1 |
| What is the default routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) Bandwidth and delay
D.) Hop count | | 2 |
| Which of the following are examples of the Session Layer?
A.) TCP
B.) LLC
C.) SQL
D.) NFS
E.) Token Ring | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
