| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Which layer of the 7 layer model is responsible for
representing the
application information between 2 different OS's? For
example, converting
ASCII to EBCIDIC.
A.) Transport
B.) Application
C.) Physical
D.) Session
E.) Presentation
F.) Network | | 2 |
| how many pass word you can configure on cisco 2500 router | HCL | 2 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
in another way writhe a confrigation which permit only mac
address trfaic through a port of your switch | | 3 |
| What is the regional telco office called, where the customers
local loop terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol?
| IBM | 15 |
| What is CSU/DSU & explain the function???? | Cisco | 3 |
| Identify the command to view the configuration-register value?
A.) show register
B.) display config-register
C.) show config
D.) show version | | 1 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 3 |
| What is the routing metric used by RIP?
A.) Route poisoning
B.) Split horizon
C.) Hop Count
D.) TTL | | 2 |
| Given the following output, how can we close Telnet session
2? (Choose two)
CCNA2620#show sessions
Conn Host Address Idle Conn Name
1 131.108.100.152 131.108.100.152 0 131.108.100.152
*2 126.102.57.63 126.102.57.63 0 126.102.57.63
❍ A. Press the Enter key and enter exit.
❍ B. Enter disconnect 2.
❍ C. Press the Enter key and enter disconnect 2.
❍ D. Enter close 2. | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| What is the standard ISDN term for a native ISDN telephone?
A.) ET
B.) TE1
C.) TE2
D.) LE
E.) TA | | 1 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to NVRAM before becoming enabled | | 1 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| You want a message to be displayed every time someone tries
to log
on to the router. Which command is required to accomplish
this task?
A.) motd#(message)#
B.) banner motd(message)
C.) banner motd#(message)#
D.) banner motd*(message)
E.) banner login#(message)# | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
