| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Tabling
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| If a frame is received at a switch and only the destination
hardware address is read before the frame is forwarded, what
type of
switching method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| Which command allows a user to see previous commands?
A.) show command
B.) CTRL-P
C.) show history
D.) CTRL-U
E.) Up Arrow
F.) SHIFT-CTRL-6 | | 1 |
| What information is provided by the local management
interface (LMI)?
A.) LMI encapsulation type
B.) The current DLCI values
C.) The status of virtual circuits
D.) The global or local significance of the DLCI values | | 1 |
| Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)# | | 1 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| An ISDN BRI circuit can be described as which of the following?
A.) 3B channels
B.) 2-64Kbps B channels and 1-16Kbps D channel
C.) none of the above
D.) 2-64Kbps B channels and 1-16Kbps C channel | | 1 |
| You are given the IP address of 172.16.2.160 with a subnet
mask of 255.255.0.0. What is the network address in binary?
A. 10101100 00010000
B. 00000010 10100000
C. 10101100 00000000
D. 11100000 11110000 | | 2 |
| On an ISDN BRI interface, the control channel is the 'D'
channel.
What is the rate of this channel?
A.) 64 Kbps
B.) 1.544 Mbps
C.) 128 Kbps
D.) 2.048 Mbps
E.) 16 Kbps | | 4 |
| What is the Difference between Hub and Switch? | | 2 |
| Which statement is true when a broadcast is sent in an
Ethernet/802.3 ITAN?
A. The ip shored used is 255.255.255.0
B. The IP address used is 255.255.255.255
C. The MAC address used is 00 00 00 00 00 00
D. The MAC address used is FF FF FF FF FF FF | | 1 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| Which of the following is a characteristic of a switch, but
not of
a repeater?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 2 |
| Which layer is responsible for routing through an internetwork?
A.) Physical
B.) Session
C.) Network
D.) Transport
E.) Application
F.) Data Link | | 1 |
| What does the acronym ARP stand for?
A.) Address Resolution Phase
B.) ARP Resolution Protocol
C.) Address Resolution Protocol
D.) Address Recall Protocol | | 2 |
| IGRP uses flash updates, poison reverse updates, holddown
times, and split horizon. How often does it broadcast its
routing table updates?
A. 90 seconds
B. 10 seconds
C. 30 seconds
D. 45 seconds | | 1 |
| You are conferring a Frame Relay router with subinterfaces
on interface Serial 0 Which subinterfaces numbers could you
use for this configuration?
A. 1 and 2
B. 0 2 and 0 3
C. 1 0 and 1 1
D. 0 1 a and 0 1 | | 1 |
| To prevent Service Advertisements (SAPs) from flooding a
network, Cisco routers do not forward them. How are
services advertised to other networks?
A. Each router builds its own SAP table and forwards that
every 60 seconds.
B. Each router assigns a service number and broadcasts
that.
C. SAPs aren't necessary with Cisco routers.
D. Cisco routers filter out all SAPs. | | 1 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
