What is the purpose of Split Horizon? A.) It prevents the regular update

Advertise your Business Here

Refer this Site

Login | Sign Up


	To Refer this Site to Your Friends Click Here

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

What is the purpose of Split Horizon?

A.) It prevents the regular update messages from reinstating
a route that

has gone down

B.) Information received on an interface cannot be sent back
out the same

interface

C.) Informs all neighbor routers that two routes exist

D.) Tells the router the destination is unreachable

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: What is the purpose of Split Horizon? A.) It prevents the regular update messages from reinstating a route that has gone down B.) Information received on an interface cannot be sent back out the same interface C.) Informs all neighbor routers that two routes exist D.) Tells the router the destination is unreachable

Answer
# 1

Answer: B

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Identify the 3 key features of the Cisco Discovery Protocol? A.) Off by default B.) Will allow for the discovery of layer 3 addresses on neighbor routers C.) Verifies connectivity D.) Open standard E.) Does not require any layer 3 protocols to be configured		1
Which of the follwing are true of standard half-duplex Ethernet circuitry? A. It is alternate one-way communication B. The receive (RX) is wired directly to the transmit (TX) of the remote station C. The transmit (TX) is wired directly to the receive (RX) of the remote station D. Collisions are not possible E. Both stations can transmit simultaneously		1
Which of the following is used to manage and monitor the network? A.) SNMP B.) HTTP C.) IP D.) FTP		2
You can access three forms of WAN services with Cisco routers. Select the three forms: A. Switched or relayed services B. Interface front end to IBM enterprise data center computers C. Using protocols that connect peer-to-peer devices like HDLC or PPP encapsulation. D. IPX/SPX E. NetBEUI		1
What is the 5-4-3-2-1 rule of network design?		3
Hi- Salmaan my name is Shadab Khan and nick Khangkp ok salmaam plz tell me about of NAT plz		3
Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode		1
What are the 2 functions of the Data Link Mac layer? A.) Handles access to shared media B.) Manages protocol access to the physical network medium C.) Provides SAPs for higher level protocols D.) Allows multiple devices to uniquely identify one another on the data link layer		1
In the setup dialog, what do the square brackets indicate? A. current or default spores B. hard coded values that cannot be modified C. values entered by the administrator but not saved D. values that must be written to NVRAM before becoming enabled		1
What is the syntax to use to configure the port on a Catalyst 5000 switch? A.) slot port/type B.) type slot/port C.) port slot/type D.) port type/slot		2
Identify the following components of the IPX address 2e.0000.0065.ed43 A.) Not a valid IPX address B.) Network = 2e, Subnet = 0000, Node = 0065.ed43 C.) Network = 2e.0000, Node = 0065.ed43 D.) Network = 2e, Node = 0000.0065.ed43		1
MIDI and MPEG are examples of what layer of the OSI seven layer model? A.) Session B.) Network C.) Datalink D.) Transport E.) Application F.) Presentation		4
7. What is an advantage to using switches in your network? A. Addressing of hosts by DHCP B. Ease of administration C. Stops broadcast storms D. Works like a repeater	iGate	2
A ISDN PRI circuit can be described as which of the following? A.) 24 B channels and 1-64Kbps D channel B.) 23 B channels and 1-64Kbps D channel C.) 2-D channels and 1-C channel D.) 2-64Kbps B channels and 1-16Kbps D channel		1
With one method for transmitting frames through a switch, the switch receives the complete frame and checks the frame CRC before forwarding the frame. What is the switch transmission method called? A. CSMA/CD B. Full Duplex C. Cut-Through D. Half-Duplex E. Fragmentation F. Store and Forward		2
why we give clock rate to DCE and not to DTE what is the difference in the two.		2
What is the default interval for SAP updates? A.) 60 seconds B.) 15 seconds C.) 30 seconds D.) 120 seconds	ACS	1
What is the default interval for SAP updates? A.) 60 seconds B.) 15 seconds C.) 30 seconds D.) 120 seconds		1
Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# access-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log		2
The -- terminal no editing -- command will perform what function? A.) Edit the contents of NVRAM B.) Allows access to the terminal port C.) Stops the advanced editing feature D.) Enable password functions		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com