| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| Identify the purpose of the wildcard mask?
A.) Match a certain portion of the IP address while ignoring
the rest of
the address
B.) Determine the class of the IP address
C.) Determine the network portion of an IP address
D.) Hide the host portion of an IP address | | 1 |
| Identify the command mode necessary to enter the extended ping
command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)# | | 1 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 3 |
| Which device listed below provides clocking for the line?
A.) DCE
B.) CPE
C.) CO
D.) DTE
E.) Demarc | | 2 |
| What does the "IPX maximum-paths 2" command accomplish?
A. It enables load sharing on 2 paths if the paths are equal
metric paths.
B. It sets up routing to go to network 2.
C. It is the default for Cisco IPX load sharing.
D. It enables load sharing on 2 paths if the paths are
unequal metric paths. | | 2 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| What are the OSPF router rules???? | NIIT | 6 |
| How many collisions are caused by transmitting and receiving
frames simultaneously in a full-duplex Ethernet technology?
A. one
B. two
C. none
D. several | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 2 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| The Datalink layer works with which of the following:
A.) Packets
B.) Bits
C.) Globules
D.) Frames
E.) Segments | | 2 |
| When using access lists, it is important where those access
lists
are placed. Which statement best describes access list
placement?
A. Put standard access lists as near the destination as
possible. Put
extended access lists as close to the source as possible.
B. Put extended access lists as near the destination as
possible. Put
standard access lists as close to the source as possible.
C. It isn't import where access lists are placed since the
router will
read and cache the whole list.
D. Put access lists as close to corporate headquarters as
possible. | | 1 |
| What is the standard ISDN term for a native ISDN telephone?
A.) ET
B.) TE1
C.) TE2
D.) LE
E.) TA | | 1 |
| What is the protocol and what is the purpose of the
following address?
238 255 255 255
A. IPX a SAP broadcast
B. IP a multicast group
C. IP a reserved address
D. IP a directed broadcast
E. IPX a flooded broadcast | | 2 |
| What utility can you use to see the path a packet takes
through an
internetwork?
A.) Route
B.) SNMP
C.) Trace
D.) Ping | | 1 |
| An autonomous system can only exist if all routers in that
system meet which criteria?
A. interconnected
B. run the same routing protocol
C. assigned same autonomous system number
D. run IGRP only
E. run RIP only | | 1 |
| What is the standard ISDN term for a native ISDN modem?
A.) ET
B.) LE
C.) TE2
D.) TE3
E.) TA | | 1 |
| what is route aggregation | | 2 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
