| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| Which protocol resolves an IP address to a MAC address?
A.) DHCP
B.) RARP
C.) ARP
D.) NBP
E.) DNS | | 3 |
| What ISDN protocol specifies concepts, terminology, and
services?
A.) Q
B.) S
C.) I
D.) E | | 1 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Eight stations connected to separate 10 Mobs pods on a Layer
2 switch will give each station how many Mobs of bandwidth?
A. 1.25
B. 4
C. 16
D. 10
E. 80 | | 1 |
| What is the administrative distance for RIP?
A.) 100
B.) 90
C.) 120
D.) 110 | | 3 |
| Your PC has been configured with IP Address 192.168.3.25
and a subnet mask of 255.255.255.0. Which of the following
IP Addresses is a valid default gateway address for your
PC?
192.168.3.0 255.255.255.0
192.168.3.2 255.255.255.0
192.168.3.25 255.255.255.0
192.168.4.1 255.255.255.255
| | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| Which symbol in the router prompt indicates you are in the
privelaged mode?
A. >
B. !
C. #
D. : | | 3 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| What is the purpose and default value of the CDP timer command?
A.) 90 seconds; interval before an entry expires
B.) 60 seconds; interval between updates
C.) 60 seconds; interval before an entry expires
D.) 90 seconds; interval between updates | | 1 |
| in which way the datas will transfer from one host to
another host by using osi layer? | | 2 |
| Can anyone explain in details the STP port state????? | | 2 |
| Which address or number is used to pass the data to the
correct application?
MAC Number
IP address
Port Number
Segment Number
| | 2 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 2 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| Which command enables directly connected network 199.55.72.0
to be used by RIP?
A. Router(config router)# rip 199.55.0.0
B. Router(config router)# rip 199.55.72.0
C. Router(config router)# network 199.55.0.0
D. Router(config router)# network 199.55.72.0 | | 1 |
| Which command should you use to create an IP standard access
list?
A. access-list standard 172.16.4.13
B. access-list 1 deny 172.16.4.13 0.0.0.0
C. access-list 100 deny 172.16.4.13 0.0.0.0
D. access-list 198 deny 172.16.4.13 255.255.255.255 | | 2 |
| How many Frame-relay encapsulation types are available with
Cisco
routers?
A.) Four
B.) Two
C.) Five
D.) Three | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
