Which of the following is a connectionless protocol at the Transport lay

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which of the following is a connectionless protocol at the

Transport layer?

A.) UDP

B.) ARP

C.) ICMP

D.) RARP

E.) IP

F.) FTP

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which of the following is a connectionless protocol at the Transport layer? A.) UDP B.) ARP C.) ICMP D.) RARP E.) IP F.) FTP

Answer
# 1

Answer: A

Is This Answer Correct ?

4 Yes

0 No

Guest

Re: Which of the following is a connectionless protocol at the Transport layer? A.) UDP B.) ARP C.) ICMP D.) RARP E.) IP F.) FTP

Answer
# 2

A.) UDP

Is This Answer Correct ?

2 Yes

1 No

Kapilasdhir
[Pioneer]

Re: Which of the following is a connectionless protocol at the Transport layer? A.) UDP B.) ARP C.) ICMP D.) RARP E.) IP F.) FTP

Answer
# 3

Udp

Is This Answer Correct ?

4 Yes

1 No

Yogesh Bhardwaj

Re: Which of the following is a connectionless protocol at the Transport layer? A.) UDP B.) ARP C.) ICMP D.) RARP E.) IP F.) FTP

Answer
# 4

E.) IP











don't forget check out http://nasriza.blogdetik.com/

Is This Answer Correct ?

0 Yes

5 No

Nasriza

Question	Asked @	Answers
Other CCNA Interview Questions


255.255.255.128/what is the n/w id ,broadcast id and the number of valid host(according to disco rules)	Reliance	2
1 what is the number of telnet session in the cisco router a 1 b 2 c 3 d 4 e 5		3
what is used for passive intercae comand mine answer-to prevent to take update from outside		1
What 2 commands verify end to end communications? A.) Trace B.) debug ip session C.) Ping D.) Route		1
What is the purpose and default value of the CDP timer command? A.) 90 seconds; interval before an entry expires B.) 60 seconds; interval between updates C.) 60 seconds; interval before an entry expires D.) 90 seconds; interval between updates		1
'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers		1
Identify 3 characteristics of a connection oriented protocol? A.) Path determination B.) Flow control C.) Acknowledgements D.) Uses hop count as metric E.) 3 way handshake		2
What does -1 signify in an extended IPX access list? A. permit this host B. deny this host C. permit only this subnet D. any host or any network		2
Hi Anyone can share the latest ICND1 (640-822)dumps updated at 30 september 2009. specialy to Jatendra if you have any updated about the ICND1 exam.will be remain thankful.		2
What is the standard ISDN term for a non-native analog telephone? A.) TE1 B.) TA C.) LE D.) TE2 E.) ET		1
Which of the following describe SMTP? A.) Used for downloading files to the router. B.) Used for sending e-mail. C.) Uses TCP. D.) Uses UDP. E.) Uses port 25. F.) Used for managing IP devices.		1
What is difference between IPv4 & IPv6??	Hathway	3
Which layer is responsible for routing through an internetwork? A.) Physical B.) Session C.) Network D.) Transport E.) Application F.) Data Link		1
Identify the 3 pieces of hardware you would not install to prevent broadcasts? A.) Switch B.) Repeater C.) Bridge D.) Router		1
Identify the command that specifies Serial 0 in slot 1? A.) Router(config)# interface serial1/1 B.) Router(config)# interface serial1/0 C.) Router(config)# interface serial0.1 D.) Router(config)# interface serial0/1		1
What is the Network Layer of the OSI responsible for? A.) Bridging B.) Routing packets through an internetwork C.) Regenerating the digital signal D.) Gateway services		1
Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Router# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes		1
Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1		1
What is the routing metric used by RIP? A.) Route poisoning B.) Split horizon C.) Hop Count D.) TTL		2
Identify the 2 rules used when configuring a Distance Vector routing protocol? A.) Physically connected network(s) B.) Configure the classful address, no subnets C.) Enable CDP so neighbors can be detected D.) Configure all networks in Area0		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com