| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | | 2 |
| 1. What is an advantage to LAN segmentation?
A. Provides multiprotocol support
B. Decreases security
C. Decreases broadcasts
D. Increases broadcasts
| | 2 |
| Identify the command to determine if an IP access-list is
grouped
on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0 | | 1 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol? | | 1 |
| Which three protocols are corerectly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| Which OSI Reference Layer is concerned with logical addressing?
A.) Network
B.) Transport
C.) Datalink
D.) Physical
E.) Session | | 1 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 2 |
| Which routing protocols uses connection-oriented routing
updates?
A.) IGRP
B.) UDP
C.) RIP
D.) IP
E.) BGP | | 2 |
| Identify the command that saves the configuration stored in
RAM to
NVRAM?
A.) copy running-config startup-config
B.) copy tftp running-config
C.) copy startup running
D.) copy active to backup | | 1 |
| Which layer is responsible for routing through an internetwork?
A.) Physical
B.) Session
C.) Network
D.) Transport
E.) Application
F.) Data Link | | 3 |
| What is link aggregration?? How many types of protocol are
used on that??? | Hathway | 3 |
| Identify the default IPX serial encapsulation?
A.) Novell-Ether
B.) SDLC
C.) SNAP
D.) HDLC | | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| Identify the type of hardware required to connect a Token ring
network to
an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| what is the difference between dynamic NAT and NAT
overload ? and how it works ?
| | 4 |
| What is the maximum number of subnets that can be assigned
to networks when using the address 172.16.0.0 with a subnet
mask of 255.255.240.0? (Assume older version UNIX
workstations are in use.)
A. 16
B. 32
C. 30
D. 14
E. It is an invalid subnet mask for the Network. | | 1 |
| Identify the 2 types of access-list filters that control SAP
traffic?
A.) Novell-ether
B.) Arpa
C.) Input-sap-filter
D.) Round-robin
E.) Output-sap-filter | | 1 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
