| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode
B.) Disconnect from the router
C.) Abort the ping operation
D.) Exits privileged exec mode | | 2 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Identify the command that configures serial0 for PPP
encapsulation?
A.) Router(config)# encapsulation ppp
B.) Router(config-if)# encapsulation serial ppp
C.) Router(config-if)# encapsulation ppp
D.) Router# encapsulation ppp | | 1 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only 4 encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.2 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encapsulation must be configured unless the
connecting routers
are both
Cisco | | 1 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 1 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing protocol?
A.) Physically connected network(s)
B.) Configure the classful address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Configure all networks in Area0 | | 1 |
| Which processes does TCP, but not UDP, use?
A. Windowing
B. Acknowledgements
C. Source Port
D. Destination Port | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from FLASH memory at the next boot?
A.) boot system flash
B.) boot system flash IOS_filename
C.) boot system IOS_filename flash
D.) boot system tftp IOS_filename tftp_address
E.) config-register 0x0102 IOS_ filename | HSBC | 1 |
| Identify IPX SAP and it's purpose?
A.) Sonet Access Pipe - interface to Sonet ring
B.) Service Advertising Protocol - advertise services
C.) Server Appletalk Protocol - appletalk directory services
D.) Service Access Point - identify upper layer protocols | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Rotuer(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| The default routing protocol for IPX is IPX RIP. How do you view
the routing updates sent and received by the router?
A.) debug ipx routing
B.) debug ipx routing activity
C.) debug rip
D.) show ipx routing
E.) sh ipx
F.) debug ipx rip | | 2 |
| Assuming no subnetting, which two pieces of information can
be derived from the IP address 144.132.25.10? (Choose two)
A. It is a Class C address
B. It is a Class B address
C. The network address is 144.0.0.0
D. The network address is 144.132.25.0
E. The host spoon of the address is 25.10 | | 2 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 2 |
| The Cisco Discovery Protocol (CDP) periodically sends out a
multicast packet (at layer 2). Which command will alter the
default
interval of 60 seconds?
A.) cdp hold 111
B.) cdp wait 111
C.) cdp interval 111
D.) cdp 111
E.) cdp timer 111 | | 1 |
| Which ISDN specification series deals with Concepts and
Terminology?
A.) World Series
B.) I- Series
C.) Q-Series
D.) 911-Series
E.) J-Series
F.) F-Series | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 1 |
| LMI operates between the Frame Switch and what other device?
A.) CPE device
B.) Another Frame Switch
C.) X.25 switch
D.) Novell File Server | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
