| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| what is the difference between
1 router and switch
2 router and hub
3 hub and switch
4 bridge and switch
| Hathway | 1 |
| the situation iz like ths -at a specific time in our company
the internet connectivity goes off...v hav two networks in
our company...but out of it only one link goes down for 5-10
sec...a fastethernet port becomes down for few sec and
automatically becomes Up...
Is this occures becoz of Power??
If yes thn y the 2nd network is not affected?? | SoftTech | 1 |
| Identify 3 characteristics of the Network layer (OSI layer 3)?
A.) Connection oriented
B.) Path determination
C.) Supports multiplexing
D.) Manages sessions
E.) Packet forwarding | | 2 |
| Which type of switching is considered to be 'wire speed?'
A.) Cut-Through
B.) Multiplexed
C.) Inverted
D.) Layer 4
E.) Store and Forward
F.) Layer 3 | | 1 |
| Which statement about the flow control function of TCP is true?
A. TCP makes no snarl to check for lost or duplicate data
packets
B. The application layer must sequence data packets when
using TCP
C. TCP controls the flow of UDP data through negative
acknowledgements (NAK)
D. TCP is a connection-oriented protocol that acknowledges
receipt of data packets and is considered reliable | | 1 |
| To monitor IP igrp traffic, you can use "debug IP igrp
transaction" or "debug IP igrp events". How do you display
information about IPX routing update packets?
A. debug routing
B. debug ipx transaction
C. debug ipx routing activity
D. debug ipx events | | 1 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 3 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 3 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| Novell NetWare has an Ethernet frame type called
Ethernet_II. What
is the matching Cisco command line keyword for this
encapsulation method?
A.) dix
B.) sap
C.) arpa
D.) gns
E.) snap
F.) novell-ether | | 1 |
| Identify the 2 characteristics regarding MAC addresses?
A.) Contains a network portion and host portion
B.) Always assigned by System Administrator
C.) 48 bits long
D.) Contains a vendor code and serial number | | 2 |
| Which command would configure Interface E0 with an IP address of
12.23.4.5 using a Subnet mask of 255.255.255.0 ?
A.) ip address 12.23.4.5 255.255.255.0
B.) ip address 12.23.4.5 /24
C.) ip address 12.23.4.5 mask 255.255.255.0
D.) ip address 12.23.4.5 mask ff:ff:ff:0
E.) that is an invalid mask for a class 'A' address | | 2 |
| Cisco routers use wildcard masking to identify how to check or
ignore corresponding IP address bits. What does setting a
wildcard mask
bit to 0 cause the router to do?
A. It tells the router to check the corresponding bit value.
B. It tells the router to ignore the corresponding bit value.
C. It tells the router to check its alternate routing list.
D. It tells the router to use its primary routing list. | | 1 |
| From Enable mode, a user types the letter 'C' and presses enter.
There is more than 1 command that starts with 'C'. What
message would
the router return?
A.) Nothing would be returned, the command is simply ignored.
B.) unknown command
C.) ambiguous command.
D.) Copy to?
E.) Configured console from console. | | 1 |
| How do you view the routers current processor utilization?
A.) show version
B.) show processes cpu
C.) show running-config
D.) show startup-config
E.) show cpu
F.) show utilization | Cisco | 2 |
| What is the purpose of Split Horizon?
A.) It prevents the regular update messages from reinstating
a route
that has gone down
B.) Information received on an interface cannot be sent back
out the
same interface
C.) Informs all neighbor routers that two routes exist
D.) Tells the router the destination is unreachable | | 1 |
| How Bridge Protocol Data Unit detect looping in Network?
How Bridge Protocol Data Unit work? explain? | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
