| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| An ISDN BRI circuit can be described as which of the following?
A.) 3B channels
B.) 2-64Kbps B channels and 1-16Kbps D channel
C.) none of the above
D.) 2-64Kbps B channels and 1-16Kbps C channel | | 1 |
| Although Cisco IOS 11.2 and later can auto-detect the LMI
type in
Frame Relay, which command will force the LMI type to q933a?
A.) frame-relay lmi-type q933a
B.) encapsulation frame-relay q933a
C.) don't need to, it is the default
D.) encapsulation q933a
E.) encapsulation frame-relay type=q933a | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| Which can be true regarding VLANs?
A.) They are created by location
B.) They are created by function
C.) They are created by department
D.) They are created by group | | 1 |
| Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)# router igrp 100
Router(config-router)# network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0 | | 1 |
| If a frame is received at a switch and only the destination
hardware address is read before the frame is forwarded, what
type of
switching method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| Identify the command to display all the valid commands at the
given mode?
A.) Help all
B.) Help
C.) All commands
D.) ? | | 3 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| Identify the command that displays the SAP table?
A.) show ipx servers
B.) display SAP table
C.) display SAP's
D.) show sap table | | 1 |
| PICT & JPEG are examples of what layer in the OSI seven
layer model?
A.) Transport
B.) Presentation
C.) Application
D.) Datalink
E.) Network
F.) Session | | 1 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 3 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport | | 2 |
| what is diffrence betwwen mpls and frame really | Volvo | 1 |
| You want to segment a network. The network is running SNA and
Netbios. Which device should NOT be used to segment the network?
A.) A store and forward switch.
B.) A router.
C.) A Catalyst 5000.
D.) A cut-through switch.
E.) A bridge. | | 1 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Tabling
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| My question is how windows pc will act as a router?
Jitendra understand this question? I again want to ask you
is it possibele for windows pc to act like a router | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
