| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| Hi, Jitendra thanks for letting me know my answer. I know
ip addressess classes & there subnet masks. Waht i want to
know is the exact address? Ex.In the organization there are
70 pcs which type of address we can use there what will be
the range for ip address? | | 2 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| hi friend i hav difficulty n need to solve it...v need to
implement a new raw switch in company as to increase the no
of staff...snc raw switch by default is in server mode,i
wanna know 1.how to make a switch in client mode...2.how to
configure switch i mean to sy how to connect all switches to
network. | | 1 |
| How many LMI types are available on Cisco routers?
A.) Four
B.) Two
C.) Five
D.) Three | | 1 |
| If a router uses static routing, how does it learn the
route to remote networks?
The router uses a RIP request to obtain remote network
numbers.
The router uses a routing protocol to exchange remote
network numbers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| Identify the definition of demarcation?
A.) Date in which the WAN service contract expires
B.) Cabling which extends from the WAN service provider to
the customer
C.) Division of responsibility, where the CPE ends and the
local loop
begins
D.) Equipment which is located at the customer premises | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | | 2 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | | 1 |
| Which OSI layer provides mechanical, electrical & procedural
specifications for activating, maintaining physical link?
A.) Presentation
B.) Network
C.) Application
D.) Physical
E.) Transport
F.) Data-Link | | 1 |
| Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router | | 1 |
| Can anyone explain the Split Horizon rule in RIP & also
Split Horizon with Poison reverse.
Jitu.... U knw wat i expect.. hehehehehe... | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| How can an Ethernet switch improve network performance?
Choose three | | 1 |
| Hi Guys i hv one confusion. Need u peoples help.
In EIGRP, maximum hop count is up to 255. By default only
100. Now question is -
a) Suppose i hv a network consist of 115 routers & EIGRP
routing protocol is configured. By default hop count is 100,
so is there any manual configuration necessary for hop count
ya router will automatically detect the hop count & will
update the hop count accordingly..?????
b) In EIGRP, Bandwidth & Delay is used to calculate metric.
For this Metric weight is set to K1(Bandwidth)=1,
K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0
Now i want, Bandwidth & Load is used to calculate metric.
For that wat i hv to configure & wat wub the metric weights.
Cud anyone explain it plzzzz..!!!! | | 5 |
| how many pass word you can configure on cisco 2500 router | HCL | 2 |
| Which addresses are INCORRECTLY paired with their class?
A. 240 - 255, Class D
B. 240 - 255, Class E
C. 224 - 239, Class D
D. 224 - 239, Class E | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
