| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is NOT a characteristic of a network segment on a switch?
A. The segment has its own collision domain
B. The segment can translate from one media to a different media
C. All devices in the segment are part of the same broadcast
domain
D. One device per segment can concurrently send frames to
the switch. | jetking | 1 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| Which frame has a Type field to identify the upper-layer
protocol?
A.) 802.3
B.) 802.2
C.) 802.5
D.) Ethernet_II | | 1 |
| Which statement about an IP network is true?
A. A broadcast source MAC address contains all zeros
B. A MAC address is part of the physical layer of the OSI model
C. MAC addresses are used by bridges to make forwarding
decisions. IP address are used by routers.
D. IP addresses allow a flat addressing scheme. MAC
addresses use a hierarchical addressing scheme. | | 2 |
| ok this is practical senario question
how can we comunicate two diffrent network host by i single
1603 sires of cisco router rember that the cisco series of
that router have singe 100mbps ethernet
now think think
write all command
answer is so simple i wiil; give the answer after 20 visit
til then wait
| | 2 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| Which command will start the process for a Cisco IOS file image
upgrade?
A.) download
B.) copy tftp flash
C.) copy flash tftp
D.) download flash
E.) network | | 2 |
| Identify the command to configure the IP address
172.16.100.5 255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 1 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| what is the binary value of loop back address | | 11 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | | 1 |
| What is the default size of a standard ping on a Cisco router?
* A: 100 bytes
* B: 32 bytes
* C: 10 bytes
* D: 16 bytes
| CMS | 2 |
| The "ipx delay number" command will allow an administrator to
change the default settings. What are the default settings?
A. For LAN interfaces, one tick; for WAN interfaces, six
ticks
B. For LAN interfaces, six ticks; for WAN interfaces, one
tick
C. For LAN interfaces, zero ticks; for WAN interfaces, five
ticks
D. For LAN interfaces, five ticks; for WAN interfaces, zero
Ticks | | 1 |
| Cisco routers can secure the enable password with a one-way hash
algorithm. What command would encrypt the enable password
with the
strong encryption method?
A.) enable encrypt john
B.) password john
C.) enable secret john
D.) enable password john
E.) secret john
F.) enable password 5 john | | 1 |
| Which layer is responsible for identifying and establishing the
availability of the intended communication partner?
A.) Application
B.) Presentation
C.) Transport
D.) Session
E.) Network | | 1 |
| What does the term "attenuation" mean in data communication?
1 loss of signal strength as distance increases
2 time for a signal to reach its destination
3 leakage of signals from one cable pair to another
4 strengthening of a signal by a networking device
| | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
