| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the standard ISDN term for a non-native analog
telephone?
A.) TE1
B.) TA
C.) LE
D.) TE2
E.) ET | | 1 |
| what is the diffrence betwwen telnet and ssh.this question
is asked by nikhil and i am plasing the answer here insteed
of his personal mail.
| | 4 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| What are hold-downs used for?
A.) To prevent regular update messages from reinstating a
route that has
come back up
B.) Information received on an interface cannot be sent back
out the
same interface
C.) To prevent regular update messages from reinstating a
route that has
gone down
D.) To hold the routing table from being sent to another router | | 1 |
| Which statement about Ethernet switches is true?
A. Symmetric switching allows connection between pods of
unlike bandwidth and does not require memory buffering
B. Memory Buffering is used to prevent a bottleneck when
pods of different bandwidth are connected on a symmetric switch
C. The latency can be reduced if the switch utilizes the
store and forward method of switching store and forward is
better for error detection
D. The cut through method of switching is faster because the
switch forwards the packet to the destination as soon as it
reads the destination address | | 1 |
| What is a characteristic of Store and Forward switches?
A.) They work at wire speed.
B.) They are the same as Cut-Through switching in 'prune' mode.
C.) They forward based on transport layer info.
D.) They forward the frame before it is completely read.
E.) They increase latency. | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| b Which protocol for PPP LCP (Link Control Protocol) performs a
challenge handshake?
A. CHAP
B. PAP
C. UDP
D. IPX | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid
Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| tell me our traditional ip routing is what
A--conectless
b----conection orented
c-----pacekt switching
d------ckt switching
slect any two
this is the question which i forgot to incoprate
next-questions
| | 3 |
| As a system administrator, you perform an extended ping at
the privileged EXEC prompt. As part of the display, you see
"Set DF bit in IP header? [yes] :" What would happen if you
answered no at the prompt.
A. This lets the router fragment the packet.
B. It tells the router not to fragment the packet.
C. This lets the router direct the packet to the destination
it finds in its routing table.
D. It tell the router to send the packet to the next hop
router. | | 1 |
| What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops | | 1 |
| (1)what is "rtp" and how it work,
(2)what is diffrence between igrp and eigrp
(3)the slection prcedure of dr and bdr is depend open
(4)why frame really is called nbma
(5)what is ppp
(6) what is diffrence b/w tcp and udp
(7) how can we implement ospf protocall on any router
(8)whta is as nomber
(9)what is AD value
(10)what is the broadcast id,n/w id and number of vallid
host of the 255.255.255.128/25 195.168.10.10/25
(11) what is stub network
(12) what is contigues n/w
(13)on which type of router we can implement default routing
(14)what is diffrence b/w hub switch;switch router,
(15)what is v lan
(16)what is the diffrence b/w link sate protocal and
distance vector protocall
(17)what is synchoransh mode of data transfer and
asynchronash mode of data transfer
(18) question on lab,
belive me frnds there are 20 questions and 5 questions on
lab implimentaion.around 1.1/2 hour i was in interview room
and after givieng 17 right answera and 4 in lab i got
slected
try to give answer
if any difficulty or any prob plz email me on
jitenderasinha.it@gmail.com
if any one of you havae boson netsim plz also intimate me
| | 4 |
| What does the term "attenuation" mean in data communication?
1 loss of signal strength as distance increases
2 time for a signal to reach its destination
3 leakage of signals from one cable pair to another
4 strengthening of a signal by a networking device
| | 1 |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| Of the following switching types, which one has the lowest
latency?
A.) Cut-through
B.) Fragment Free
C.) None
D.) Store-and-forward | | 1 |
| What are the difference between IPv4 & IPv6?? Can anyone
explain more details about it..!! | HCL | 4 |
| Identify the type of routing protocol that maintains a
topological
database of the network?
A.) Topological state
B.) Shortest Path First
C.) Link state
D.) Distance vector | | 1 |
| When a Distance Vector routing protocol detects that a connected
network has gone down, it sends out a special routing update
packet,
telling all directly connected routers that the distance to
the dead
network is infinity. This is an example of which routing
technology?
A.) ICMP.
B.) Only Link State routing protocols have this intelligence.
C.) Triggered updates.
D.) Garrison-4.
E.) Split Horizon.
F.) Poison Reverse. | | 1 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| |
| For more CCNA Interview Questions Click Here |