| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 2 |
| what is the need og
jitu(config)#ip helper address <ip address>
can any one exaplain it briefly
specially shain i am looking towards you.Becoz you are the
only one who can solve my that problem not even jitendera sinha | | 3 |
| If configuring a Cisco router to connect to a non-Cisco router
across a Frame Relay network, which encapsulation type would
you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| Which three protocols are correctly matched to their
transport layer functions? (Choose three)
A. route selection IP
B. sliding window UDP
C. well known pods IP
D. route validation ICMP
E. connection oriented TCP
F. three-way handshake TCP
G. no sequence and acknowledgement UDP | | 1 |
| what is 5-4-3 rule? | | 1 |
| Identify the following command to configure a secret password to
'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco | | 1 |
| Which EXEC command displays system hardwarde configuration
information software version and the names and sources of
configuration files and boot images on a router?
A. show boot
B. show flash
C. show config
D. show version | | 1 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 3 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| The Cisco IOS is stored in:
A.) ROM
B.) CD
C.) Flash
D.) NVRAM | | 3 |
| What are the OSPF router rules???? | NIIT | 6 |
| Identify the command mode necessary to enter the extended ping
command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)# | | 1 |
| Which OSI Reference Layer controls application to application
communication?
A.) Datalink
B.) Network
C.) Transport
D.) Session
E.) Physical | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| Which of the following will show an extended access list 150?
A.) sh access-list
B.) sh ip int
C.) sh ip access-list 150
D.) sh access-list 150 extended | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| Identify 3 characteristics of a MAC address?
A.) Burned into the NIC
B.) 48 bits long
C.) Length is 32 bits
D.) Used to identify a host device
E.) Contains a network portion and a host portion | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
