| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
in another way writhe a confrigation which permit only mac
address trfaic through a port of your switch | | 3 |
| After the command -- router igrp 200 -- what command would
enable
IGRP on the router for interface E0, with an address of
157.89.4.4 and a
mask of 255.255.255.0 ?
A.) network 157.89.4.0 255.255.255.1
B.) network 157.89.0.0
C.) router igrp *
D.) router igrp 157.89.0.1
E.) router igrp int e1
F.) router igrp 157.89.4.1 | | 2 |
| What are four benefits that can result from applying ISDN
networking? (Choose four)
A. Full time connectivity across the ISDN is spoofed by
Cisco IOS routers using dial on demand routing (DDR)
B. Small Once and Home Once sites can be economically
supported with ISDN Basic Rate Interface (BRI) servkps
C. ISDN replaces Signaling System 7 (SS7) in the Public
Switched Telephone Network (PSTIC) backbone
D. ISDN can be used as a backup service for a leased line
connection between the remote and central chaps
E. Modem racking and cabling can be eliminated by
integration of digital modem cards on Cisco IOS Network
Acess Servers (NAS) | | 2 |
| what is difference between
1 pap and chap(quite easy but need on line answer)
2 chap and ms-chap(plz describe briefly)
now i have posted the question is there any one to help me?
| | 1 |
| Which memory component on a Cisco router contains the
dynamic system configuration?
ROM
NVRAM
Flash
RAM/DRAM | HCL | 16 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| hi friends i am jitendera kumar sinha.i have a question in
mind that what is the diffrence between router and l3 switch
i serched on google and found that switch L3 is best in lan
and router are best in wan and switch are more faster then
router.beside that any short of technical diffrence if you
body know then plz plz and plz reply.
my 2nd question is that why we canot replace router with L3
switches (donot tell that it is costly then router).i want
any technical cause.
this is 1 am hope in noon when ever i logg again i will find
the answer posted by you.
thanks onse again
plz pzl make reply
thanks
jitendera kumar sinha
jitenerasinha.it@gmail.com
| | 5 |
| A network is vow congested currently all the devices are
connected through a hub. Which would best decrease
congestion on this network?
A. add a second hub
B. replace the hub with a router
C. replace the hub with a switch
D. replace the hub with a repeater | | 1 |
| There is an emergency fall-back 'skeleton' IOS stored in
read only
memory on all Cisco routers. What command would make the
router load the
IOS from
Read Only Memory?
A.) reload rom
B.) boot system rom
C.) load ios bootflash
D.) load ios rom
E.) bootsystem skeleton | | 2 |
| What does a metric of 16 hops represent when using RIP?
A.) Number of hops to the destination
B.) Destination unreachable
C.) Number of routers
D.) Bandwidth | | 3 |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| Identify the type of routing protocol that maintains a
topological
database of the network?
A.) Topological state
B.) Shortest Path First
C.) Link state
D.) Distance vector | | 1 |
| Identify the mode reflected by the following prompt 'Router'?
A.) Setup
B.) RXBoot
C.) Boot mode
D.) Privileged exec mode | | 1 |
| what is stp. | IBM | 3 |
| Which of the following provide correct information about a
protocol at the
transport layer of the OSI model?
A.) UDP - Provides Connectionless datagrams service
B.) TCP - Provides Connection Oriented Services
C.) SMTP - Provides Mail Exchange
D.) IP - Route determination
E.) TCP - Provides Flow Control and Error Checking
F.) FTP - Transfers of Files | | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| What is the Broadcast IP Address? | | 11 |
| What is ISR or NonISR router? Difference between ISR or
NonISR router? | HCL | 3 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
