| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Novell NetWare has an Ethernet frame type called Ethernet_802.2.
What is the matching Cisco command line keyword for this
encapsulation
method?
A.) gns
B.) arpa
C.) snap
D.) sap
E.) novell-ether
F.) dix | | 1 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup | | 1 |
| What is the function of Layer 2 Switch? | | 1 |
| Identify the command to configure the IP address
172.16.100.5 255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 1 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 1 |
| On an ISDN BRI interface, the control channel is the 'D'
channel.
What is
the rate of this channel?
A.) 64 Kbps
B.) 1.544 Mbps
C.) 128 Kbps
D.) 2.048 Mbps
E.) 16 Kbps | | 2 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| Dear Mr.Shahin thank you very much for your advise i realy
thanks full to you.
Best of luck | | 2 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 1 |
| When a Distance Vector routing protocol detects that a connected
network has gone down, it sends out a special routing update
packet,
telling all directly connected routers that the distance to
the dead
network is infinity. This is an example of which routing
technology?
A.) ICMP.
B.) Only Link State routing protocols have this intelligence.
C.) Triggered updates.
D.) Garrison-4.
E.) Split Horizon.
F.) Poison Reverse. | | 1 |
| Identify 3 characteristics of a MAC address?
A.) Burned into the NIC
B.) 48 bits long
C.) Length is 32 bits
D.) Used to identify a host device
E.) Contains a network portion and a host portion | | 2 |
| Which of the following is an invalid host address using a
netmask
of 255.255.255.192?
A.) 10.1.1.1
B.) 10.1.1.66
C.) 10.1.1.130
D.) 10.1.1.127 | | 2 |
| Which protocol will let neighbor routers know if your
internetwork
experienced congestion on a serial port?
A.) BootP
B.) IP
C.) ICMP
D.) ARP
E.) FTP
F.) RARP | | 2 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 1 |
| Which two commands show your access lists? (Choose two)
A. show filters
B. show access-lists
C. show ip access-lists
D. show running-config | | 1 |
| Which OSI layer incorporates the MAC address and the LLC?
A.) Data link
B.) Network
C.) Physcial
D.) Transport | | 3 |
| The maximum distance on a 10BaseT network from the hub to a
workstation is which of the following?
A.) 500 meters
B.) 1000 meters
C.) 100 meters
D.) 1500 meters | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
