| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which two statements accurately define IP addressing rules?
(Choose two)
A. IP multicast addresses start with 240
B. A host Carbon of all 1 a indicates a network broadcast
C. The value of zero (0) in the host Carbon means all hosts
on the network
D. IP addresses are four octets long and contain a network
Carbon and a host Carbon | | 1 |
| What parameter is used with statically assigned routers to tell
packets
which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface | | 1 |
| How many valid host IP addresses are available on the
following network/subnetwork? 176.12.44.161/30
A. 2
B. 30
C. 254
D. 16,382
E. 65,534 | | 1 |
| Identify the IPX standard access-list number range?
A.) 600 - 699
B.) 1000 - 1099
C.) 1 - 99
D.) 100 - 199
E.) 800 - 899 | | 1 |
| Hello every one. Please can any one explain me the
difference b/w Cisco Switch/ws-c3560-24ps-s and Switch/ws-
c3560-24ts-s. what is does PS & TS Stands for. Waiting for
your passtive reply. Wish You all the best | | 2 |
| Switching methods include cut-through, store and forward,
and a modified version of the first two methods. Which
statement about switching methods is true?
A. The store and forward method has low latency
B. The cut through method of switching has high latency
C. The modified version holds the packet in memory until 50
percent of the packet reaches the switch
D. The modified version holds the packet in memory until the
data spoon of the packet reaches the switch | | 3 |
| Identify the order of the 5 step encapsulation?
1) Create the segment
2) Convert the frame to bits
3) Create the packet
4) Create the frame
5) User creates the data
A.) 1,2,4,2,5
B.) 2,1,3,4,5
C.) 5,1,3,4,2
D.) 5,3,4,1,2 | | 1 |
| Which of the following are Session Layer standards?
A.) ASCII and EBCDIC
B.) MPEG and MIDI
C.) RPC and SQL
D.) JPEG and PICT | | 1 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
mac-address 0005.1b00.5b58 | | 4 |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 1 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 2 |
| What is the protocol number for UDP?
A.) 6
B.) 17
C.) 25
D.) 21 | | 1 |
| When determining whether or not to route a LAN segment,
which rule of
thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| LAN stands for which of the following?
A.) Local Area Network
B.) Local Arena Network
C.) Local Area News
D.) Logical Area Network | | 4 |
| Which of the following are examples of the Session Layer?
A.) IP
B.) Netbios Names
C.) NFS
D.) Token Ring
E.) SQL
F.) RPC | | 2 |
| what are two security appliances that can be installed a
network | | 7 |
| what is telnet,ssh??
what is the perpose of this?
wer r this configured and how to configured?? | | 2 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| . Which command sequence will allow only traffic from
network 185.64.0.0 to enter interface s0?
A. access-list 25 permit 185.64.0.0 255.255.0.0
int s0 ; ip access-list 25 out
B. access-list 25 permit 185.64.0.0 255.255.0.0
int s0 ; ip access-group 25 out
C. access-list 25 permit 185.64.0.0 0.0.255.255
int s0 ; ip access-list 25 in
D. access-list 25 permit 185.64.0.0 0.0.255.255
int s0 ; ip access-group 25 in | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
