| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 1 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 3 |
| What is a disadvantage of using a connection oriented
protocal such as TCP?
A. Packet acknowledgement may add overhead
B. packets are not tagged with sequence numbers
C. Loss or duplication of data packets is more likely to occur
D. The application layer must assume responsibility for
correct searchers of the data packets | | 1 |
| Which command should you use to confound a router so that it
can become a TFTP server host for a router system image that
is run in a Flash?
A. copy flash tftp
B. config tftp server
C. write, network -router name-
D. tftp-server system -file name-
E. setup server tftp -system name- | | 1 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| What is the protocol number for UDP?
A.) 6
B.) 17
C.) 25
D.) 21 | | 2 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| If a frame is received at a switch and only the destination
hardware
address is read before the frame is forwarded, what type of
switching
method is this?
A.) Store-and-drop
B.) Latency
C.) Store-and-forward
D.) Cut-through | | 1 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 2 |
| What is SIA (Stuck in Active) in EIGRP? | Hathway | 4 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| Identify the 4 that are WAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | | 2 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| Which two statements about frame tagging are true? (Choose two)
A. A filtering table is developed for each switch.
B. Frame tagging assigns a unique user defined ID to each frame.
C. A unique identifier is placed in the header of each frame
as it is forwarded between switches.
D. Frame tagging is a technique that examines particular
information about each frame based on user defined offsets. | | 2 |
| What is required to support full-duplex Ethernet?
A.) Multiple paths between multiple stations on a link
B.) Automatic sensing operation by all connected stations
C.) Loopback and collision detection disabled
D.) Full-duplex NIC cards | | 1 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home.
D. a standard 28.8 analog dialup connection to the user at home. | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
