| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does a router change in a packet when it forwards a
packet to the next hop?
* A: Destination physical address
* B: Destination network address
* C: Destination network address and the destination
physical address
| Microland | 7 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| When determining whether or not to route a LAN segment,
which rule
of thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future? | | 3 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| What is the Difference between Switch and Bridge? | | 3 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 1 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecing to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecing to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 1 |
| In order to enable RIP, which two tasks need to be
performed? (choose two)
A. Specify the routing protocol
B. Confound static RIP routes
C. Specify directly connected subnets
D. Specify directly connected networks | | 1 |
| hi friend i hav difficulty n need to solve it...v need to
implement a new raw switch in company as to increase the no
of staff...snc raw switch by default is in server mode,i
wanna know 1.how to make a switch in client mode...2.how to
configure switch i mean to sy how to connect all switches to
network. | | 1 |
| What is the function of Layer 2 Switch? | | 1 |
| There is an emergency fall-back 'skeleton' IOS stored in
read only
memory on all Cisco routers. What command would make the
router load the
IOS from
Read Only Memory?
A.) reload rom
B.) boot system rom
C.) load ios bootflash
D.) load ios rom
E.) bootsystem skeleton | | 2 |
| what is the need og
jitu(config)#ip helper address <ip address>
can any one exaplain it briefly
specially shain i am looking towards you.Becoz you are the
only one who can solve my that problem not even jitendera sinha | | 3 |
| Which two describe frame tagging?
A.) Examines particular info about each frame
B.) A unique ID placed in the header of each frame as it
traverses the
switch fabric
C.) A user- assigned ID defined to each frame
D.) The building of filter tables | | 1 |
| hi... i am a beginner to CCNA... i find it hard understandin
collision domain n broadcast domain.. please don tell me the
definition.. i read the definitions many times... i need a
more detailed explanation... like whn i read the definition
it sounds simple... but i don understand whn they say it
like a hub has one collision domain and one broadcast
domain... and if collisions happen inside collision
domain... i am confused... please help me... :( | | 4 |
| What is an advantage of LAN segmentation?
A.) Increases broadcasts.
B.) Increases collisions.
C.) Provides more protocol support.
D.) Decreases broadcasts.
E.) Routing protocol support. | Wipro | 2 |
| Which statement is true regarding Administrative distance?
A.) It is a metric
B.) Number of hops between two routers
C.) Trustworthiness of the routing information
D.) RIP Administrative distance is 100 | TCS | 1 |
| here is your question sahin
Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight
is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1,
K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP.
I knew about it from ICND 2 cisco press book.
Three more questions -
a) If we change the K value (I mean metric weight)on a
router what will happen???
b) When redistribution is necessary in EIGRP. Is there any
condition for that???
c) What is reference bandwidth for metric calculation in
EIGRP. As we know, in OSPF, on a CISCO router reference
bandwidth is 10Mbps. | | 3 |
| Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup | | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
