Identify 3 methods not used to prevent routing loops? A.) Holddown timer

Advertise your Business Here

Refer this Site

Login | Sign Up


	To Refer this Site to Your Friends Click Here

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Identify 3 methods not used to prevent routing loops?

A.) Holddown timers

B.) Sequence numbers

C.) Triggered updates

D.) Split horizon

E.) Area hierarchies

F.) Order of router startup

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Identify 3 methods not used to prevent routing loops? A.) Holddown timers B.) Sequence numbers C.) Triggered updates D.) Split horizon E.) Area hierarchies F.) Order of router startup

Answer
# 1

Answer: B E F

Is This Answer Correct ?

5 Yes

2 No

Guest

Re: Identify 3 methods not used to prevent routing loops? A.) Holddown timers B.) Sequence numbers C.) Triggered updates D.) Split horizon E.) Area hierarchies F.) Order of router startup

Answer
# 2

A.) Holddown timers-No updates are entertained

C.) Triggered updates-triggering that there is route posining

D.) Split horizon-no return updates that I have updated

Is This Answer Correct ?

2 Yes

4 No

Muheed

Re: Identify 3 methods not used to prevent routing loops? A.) Holddown timers B.) Sequence numbers C.) Triggered updates D.) Split horizon E.) Area hierarchies F.) Order of router startup

Answer
# 3

A & D

Is This Answer Correct ?

1 Yes

0 No

Question	Asked @	Answers
Other CCNA Interview Questions


Identify 3 characteristics of ISDN? A.) Transports voice and data B.) Transports voice only C.) Support both BRI and PRI D.) Runs over existing phone lines E.) Same as X.25		1
What information can you get from CDP info: (choose all that apply) A.) Hardware platform B.) One address per protocol C.) Software platform D.) Hostname E.) The same info as show version F.) Incoming/outgoing port		1
For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet interface? A.) novell-ether B.) gns C.) snap D.) arpa E.) sap F.) dix		1
Which protocol works at the Internet layer and is responsible for making routing decisions? A.) UDP B.) IP C.) TCP D.) ARP		3
Which type of switching reads in the entire frame before forwarding it? A.) Tabling B.) Store-and-Forward C.) Inverse ARP D.) Fast Forward E.) Cut-Through F.) Routing		1
You just entered the following command_Router(config#) line console 0 Which operation is most likely to follow? A. Confound terminal type B. enter protocol parameters for a serial line C. create a password on the console terminal line D. establish a terminal type 4 connection to a remote host E. change from configuration mode to console privileged mode	Wipro	10
In distance-vector routing, there is a problem known as the 'count to infinity' problem. What is the most direct solution to this? A.) Defining a Maximum. B.) You can not solve the 'count to infinity' problem with a distance vector protocol. C.) Poison Reverse. D.) Triggered Updates. E.) Split Horizon.		1
Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# acess-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log	HCL	2
What is the purpose of the DLCI? A.) Identifies the remote routers B.) Contained with a 802.2 frame for routing purposes C.) Used with PPP during authentication D.) Identifies the PVC in a Frame Relay network		1
Which addresses are valid host addresses? A. 201.222.5.17 B. 201.222.5.18 C. 201.222.5.16 D. 201.222.5.19 E. 201.222.5.31		2
If you have configured IPX on a Serial interface, which command would display the IPX network and node address on the Serial 1 interface? A.) show interface B.) show ipx s1 C.) show interface s1 D.) show ipx int serial 1 E.) show ipx int brief		1
Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102		1
Which configuration mode and command combination sets the bandwidth metric of a Frame Relay connection? A. router(config)# clock rate 56 B. router(config)# bandwidth 56 C. router(config)# bandwidth 56000 D. router(config)# clock rate 56000		2
8. When is Frame Tagging used? A. When you install repeaters in your network B. When you install bridges in your network C. When you install routers in your network D. When you use Switches configured with multiple VLANS		4
What is the default encapsulation of Netware 3.12? A.) Ethernet_II B.) 802.5 C.) 802.2 D.) 802.3		1
A ISDN PRI circuit can be described as which of the following? A.) 24 B channels and 1-64Kbps D channel B.) 23 B channels and 1-64Kbps D channel C.) 2-D channels and 1-C channel D.) 2-64Kbps B channels and 1-16Kbps D channel		1
Identify the command that specifies Serial 0 in slot 1? A.) Router(config)# interface serial1/1 B.) Router(config)# interface serial1/0 C.) Router(config)# interface serial0.1 D.) Router(config)# interface serial0/1		1
What is the protocol number for TCP? A.) 80 B.) 21 C.) 11 D.) 6		1
What is the extended IPX access list range? A.) 901-1000 B.) 100-199 C.) 900-999 D.) 1000-1000		1
Which two encapsulation names are correctly paired with the Cisco IOS encapsulation names? (Choose two) A. Ethernet_II-ARPA B. Ethernet_802.3-SAP C. Ethernet_802.2-LLC D. Ethernet_SNAP-SNAP		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com