| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| When you cords an IP address on a place router which command
stale the IP processing on the interface?
A. ip enable
B. network ip-address
C. ip address ip-address subnet mask
D. the exit command from the enabled configuration
E. copy running-configuration to startup-configuration | | 3 |
| R1#sh ip nat translations
Pro Inside global Inside local Outside local
Outside global
icmp 15.1.1.1:11 10.1.1.1:11 30.1.1.1:11
30.1.1.1:11
icmp 15.1.1.1:12 10.1.1.1:12 20.1.1.1:12
20.1.1.1:12
icmp 15.1.1.1:13 10.1.1.1:13 21.1.1.1:13
21.1.1.1:13
icmp 15.1.1.1:14 10.1.1.1:14 31.1.1.1:14
31.1.1.1:14
R1#
So my question is that after every ip address [:] is used &
some number. 15.1.1.1{:11}... what is this colon & number
indicate.
Can anyone tel me this..!!!
Thanking you advance.
Shahin | | 3 |
| What is the command to copy the IOS image to a TFTP server?
A.) copy flash tftp
B.) copy running-config tftp
C.) copy ios tftp
D.) copy startup-config tftp | | 2 |
| The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport | | 1 |
| What protocols can you use while testing Trace?
A.) DECnet
B.) CLNS
C.) IP
D.) Old Vines
E.) Vines
F.) Chaos | | 1 |
| Given the IPX address 4a.0002.1111.a999, what is the network ID
and what is the node ID?
A.) net 4a host 0002.1111.a999
B.) net a999 node 0002.1111
C.) net 0002.1111.a999 node 4a
D.) net 0002.1111 node a999 | | 1 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| Which two statements accurately define IP addressing rules?
(Choose two)
A. IP multicast addresses start with 240
B. A host Carbon of all 1 a indicates a network broadcast
C. The value of zero (0) in the host Carbon means all hosts
on the network
D. IP addresses are four octets long and contain a network
Carbon and a host Carbon | | 1 |
| What three occurrences will reset the holddown timer after a
triggered update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| what is nat.types of nat | | 3 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS
PREFERED OVER ANY NETWORK PROTOCOL? | Bank-Of-India | 1 |
| IP standard access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) port
C.) protocol
D.) source address | | 2 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| From Enable mode, a user types the letter 'C' and presses enter.
There is more than 1 command that starts with 'C'. What
message would
the router return?
A.) Nothing would be returned, the command is simply ignored.
B.) unknown command
C.) ambiguous command.
D.) Copy to?
E.) Configured console from console. | | 1 |
| Which statement is true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not a the same
time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| What are the two types of access lists that can be
configured on a
Cisco router?
A. Standard
B. Extended
C. Filtering
D. Packet | | 1 |
| What is the routing metric used by RIP?
A.) Route poisoning
B.) Split horizon
C.) Hop Count
D.) TTL | | 1 |
| Identify the purpose of the following command 'ip route
192.168.100.0 255.255.255.0 10.1.0.1'
A.) Enabling a dynamic routing protocol
B.) Creating a static route to the 10.1.0.0 network
C.) Teaches the router about the distant network
192.168.100.0 and how
it can be reached via 10.1.0.1
D.) Assigning the IP address 192.168.100.0 to an interface | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
