Identify the purpose of the following command 'ip route 192.168.100.0

Advertise your Business Here

Refer this Site

Login | Sign Up


	SiteMap shows list of All Categories in this site.

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Identify the purpose of the following command 'ip route
192.168.100.0

255.255.255.0 10.1.0.1'

A.) Enabling a dynamic routing protocol

B.) Creating a static route to the 10.1.0.0 network

C.) Teaches the router about the distant network
192.168.100.0 and how it

can be reached via 10.1.0.1

D.) Assigining the IP address 192.168.100.0 to an interface

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Identify the purpose of the following command 'ip route 192.168.100.0 255.255.255.0 10.1.0.1' A.) Enabling a dynamic routing protocol B.) Creating a static route to the 10.1.0.0 network C.) Teaches the router about the distant network 192.168.100.0 and how it can be reached via 10.1.0.1 D.) Assigining the IP address 192.168.100.0 to an interface

Answer
# 1

Answer: C

Is This Answer Correct ?

1 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface		1
Which of the following would be displayed by the command 'SHOW CDP NEIGHBOR DETAIL'? A.) The incoming/outgoing port. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.		1
What is masking? why is needed?		4
What is the first step in data encapsulation? A.) User information is converted into data. B.) Frames are put into bits. C.) Data is converted into segments. D.) Segments are converted into datagrams and packets. E.) Packets are put into logical frame.		1
Of the following switching types, which one has the lowest latency? A.) Cut-through B.) Fragment Free C.) None D.) Store-and-forward		1
Which of the following is true regarding standard ISDN BRI service? A.) ISDN BRI B channels are typically 64K. B.) ISDN BRI can handle only voice. C.) ISDN BRI can handle only data. D.) ISDN BRI has 2B and 1D channels. E.) ISDN BRI D channels are 16K. F.) ISDN BRI can handle voice and data.		2
You have a Class B network address divided into 30 subnets. You will add 25 new subnets within the next year. You need 600 host IDs for each subnet. Which subnet mask should you use? A.) 255.254.0.0 B.) 255.192.0.0 C.) 255.255.252.0 D.) 255.255.248 0		1
Which 3 statements describe default encapsulation and LMI type configuration? A.) There are only four encapsulations and 3 LMI type options B.) The LMI type config term options C.) In release 11.3 the LMI type is autosensed D.) The default LMI is Cisco E.) IETF encap must be configured unless the connecting routers are both cisco		1
"sap" is used by the Cisco IOS for which encapsulation types? A. Ethernet_802.2 B. Token-Ring C. FDDI_SNAP D. Ethernet_802.3 E. FDDI_802.2		1
Identify the 4 that are not LAN technologies? A.) HDLC B.) FDDI C.) 802.5 D.) HSSI E.) SDLC F.) Frame Relay	AXA	1
Which address or number is used to pass the data to the correct application? MAC Number IP address Port Number Segment Number		2
Identify 3 methods used to prevent routing loops? A.) Split horizon B.) Holddown timers C.) Poison reverse D.) SPF algorithm E.) LSP's		2
What is the purpose of the DLCI? A.) Identifies the remote routers B.) Contained with a 802.2 frame for routing purposes C.) Used with PPP during authentication D.) Identifies the PVC in a Frame Relay network		1
The Cisco Catalyst 5000 switch supports full duplex. How would you enable it on the second port of the card in slot 1? A.) router(config-if)# duplex full B.) router(config)# duplex full C.) router(config-if)# set port duplex D.) router(config)#port duplex = full E.) router(config-if)# set port 1/2 full		1
Identify 2 HDLC characteristics? A.) Default serial encapsulation B.) Open standard C.) Supports Stacker compression D.) Supports point-to-point and multipoint		1
What command can you type to view the connections after telneting into multiple routers simultaneously? A.) sh users B.) sh ports C.) sh host D.) sh sessions		1
Which command will show you if you have a DTE or DCE cable connected to an interface?		3
Which two steps are part of the process of creating Frame Relay subinterfaces on a point to point connection? (Choose two) A. configure the router to forward all broadcast packets B. remove any network address assigned to the physical interface C. configure the local data link connection identifier (DICI) for the subinterfaces D. cartoon the total committed information rate (CIP) available among the subinterfaces		1
A ISDN PRI circuit can be described as which of the following? A.) 24 B channels and 1-64Kbps D channel B.) 23 B channels and 1-64Kbps D channel C.) 2-D channels and 1-C channel D.) 2-64Kbps B channels and 1-16Kbps D channel		1
Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com