| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the order of the 5 step encapsulation?
1) Create the segment
2) Convert the frame to bits
3) Create the packet
4) Create the frame
5) User creates the data
A.) 1,2,4,2,5
B.) 2,1,3,4,5
C.) 5,1,3,4,2
D.) 5,3,4,1,2 | | 1 |
| Identify the type of routing protocol that exchanges entire
routing tables at regular intervals?
A.) Link state
B.) Interior gateway protocols
C.) Appletalk routing
D.) Distance vector | | 1 |
| Which statements are true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not at the
same time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| Identify IPX GNS and it's purpose?
A.) Go Network Server - sends a print job to a network server
B.) Get Nearest Server - locate the nearest server
C.) Guaranteed Network Services - allocates resources to users
D.) Get Notes Server - locates Domino Server | | 1 |
| why we give clock rate to DCE and not to DTE
what is the difference in the two. | | 2 |
| In transport layer, for connection oriented communication
Three way handshake process is there to establish a
connection. So question is that, when a host send an ACK
messages to another host with host intend to establish a
connection, the source host send it as Broadcast or unicast
message? Cud anyone explain this.
Thanks in advance. | HCL | 3 |
| What field tells the Internet layer how to handle an IP packet?
A. Type of Service
B. Identification
C. Flags
D. Frag Offset | | 1 |
| What is the function of the Transport layer and which protocols
reside
there?
A.) MAC addressing - IP
B.) Interhost communication - SQL, NFS
C.) Best effort Packet delivery - TCP, UDP
D.) End-to-end connections - TCP, UDP | | 1 |
| Identify the purpose of ARP?
A.) Avoiding routing loops
B.) Determining a workstation's IP address
C.) Sending a directed broadcast
D.) Determining a workstation's MAC address | | 3 |
| Where shall i do CCNA cour??. can i do CCNA at home if yes
then where shall i get CCNA book or simmulator.or if not
then plz reff. me any good center in delhi | | 1 |
| What is link aggregration?? How many types of protocol are
used on that??? | Hathway | 3 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE cables. To which router would you add the clockrate
command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | TCS | 3 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from the Network File server at
1.2.3.4
during the next boot?
A.) boot system flash IOS_filename 1.2.3.4
B.) boot system tftp IOS_filename 1.2.3.4
C.) config-register 0x0 1.2.3.4
D.) boot system rom 1.2.3.4
E.) This can not be done, only the first file in flash can
be used. | | 1 |
| thnx jitender...its me shridh...m working for SG ltd..the
situation iz like ths -at a specific time in our company the
internet connectivity goes off...v hav two networks in our
company...but out of it only one link goes down for 5-10
sec...a fastethernet port becomes down for few sec and
automatically becomes Up... Is this occures becoz of Power??
If yes thn y the 2nd network is not affected??
plz tel me jitender how to resolve ths problem?
as u sd loop in switch is the primary cause of ths....i
wanna know how to resolve it...thnx for ur replys jitender
sinha. | | 2 |
| A default route is analogous to a _________.
A. default gateway
B. static route
C. dynamic route
D. one-way route | | 1 |
| Which of the following use PVCs at layer 2?
A.) X.25
B.) HDLC
C.) Frame relay
D.) ISDN | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing protocol?
A.) Physically connected network(s)
B.) Configure the classful address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Configure all networks in Area0 | | 1 |
| Which OSI layer provides mechanical, electrical, procedural for
activating, maintaining physical link?
A.) Presentation
B.) Network
C.) Application
D.) Physical
E.) Transport
F.) Data-Link | | 2 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
