| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following is an example of a Transport Layer
protocol?
Ethernet
IP
TCP
RS-232
| | 1 |
| Which command successfully pings an individual IP address?
A. Router> ping 192.5.5.0
B. Router# ping 192.5.5.30
C. Router> ping 192.5.5.256
D. Router# ping 192.5.5.255 | | 2 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 2 |
| Which two statements about a reliable connection oriented
data transfer are true? (Choose two)
A. recipients acknolwedge receipt of data
B. when tankers are filled to capacity, datagrams are
discarded and not retransmitted
C. windows are used to control the amount in outstanding
unacknowledged data segments
D. if the sender a timer expires before receipt of an
acknowledgement the sender drops the connection
E. The receiving device waits for acknowledgements from the
sending device before accepting more data segments | | 1 |
| Which of the following provide connection-oriented transport
to upper
layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| Hi Guys i hv one confusion. Need u peoples help.
In EIGRP, maximum hop count is up to 255. By default only
100. Now question is -
a) Suppose i hv a network consist of 115 routers & EIGRP
routing protocol is configured. By default hop count is 100,
so is there any manual configuration necessary for hop count
ya router will automatically detect the hop count & will
update the hop count accordingly..?????
b) In EIGRP, Bandwidth & Delay is used to calculate metric.
For this Metric weight is set to K1(Bandwidth)=1,
K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0
Now i want, Bandwidth & Load is used to calculate metric.
For that wat i hv to configure & wat wub the metric weights.
Cud anyone explain it plzzzz..!!!! | | 5 |
| Which is true regarding half duplex Ethernet operation?
A.) Half Duplex ethernet technology provides a transmit circuit
connection wired directly to the receiver circuit at the
other end
B.) Half duplex transmission between stations is achieved by
using point
to multipoint Ethernet and Fast Ethernet
C.) With Half Duplex transmission logically circuits feed
into a single
cable creating a situation similar to a one way bridge
D.) Half Duplex transmission between stations is achieved
using Point to
Point Ethernet & Fast Ethernet | | 1 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Identify the extended IP access-list number range?
A.) 600 - 699
B.) 1 - 99
C.) 900 - 999
D.) 100 - 199 | | 2 |
| Which command specifies a second subinterface on serial
interface 0?
A. interface s 0.2 point-to-point
B. interface 2 s.0 point-to-point
C. suberinterface 2.s 0 point-to-point
D. interface s 0 sub 2 point-to-point
E. interface s 0.1 point-to-point sub 2 | | 1 |
| Which statement about an IP network is true?
A. A broadcast source MAC address contains all zeros
B. A MAC address is part of the physical layer of the OSI model
C. MAC addresses are used by bridges to make forwarding
decisions. IP address are used by routers.
D. IP addresses allow a flat addressing scheme. MAC
addresses use a hierarchical addressing scheme. | | 2 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| Which of the following are examples of the Transport Layer?
A.) Token Ring
B.) UDP
C.) TCP
D.) IP
E.) SQL
F.) LLC | | 1 |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 1 |
| Which statement should you use to deny FTP access (only)
from network 210 93 105 0 to network 223 8 151 0?
A. access list 1 deny 210 93 105 0 0 0 0 0 any eq ftp access
list 1 permit any
B. access list 100 deny tcp 210 93 105 0 0 0 0 255 223 8 151
0 0 0 0 255 eq ftp
C. access list 100 deny ip 223 8 151 0 0 0 0 255 any eq ftp
access list 100 permit hp any any
D. access list 100 deny tcp 210 93 105 0 0 0 0 255 223 8 151
0 0 0 0 255 eq ftp access list 100 permit ip any any | | 1 |
| Hi, Jitendra thanks for letting me know my answer. I know
ip addressess classes & there subnet masks. Waht i want to
know is the exact address? Ex.In the organization there are
70 pcs which type of address we can use there what will be
the range for ip address? | | 2 |
| Which of the following are examples of the Session Layer?
A.) TCP
B.) LLC
C.) SQL
D.) NFS
E.) Token Ring | | 1 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| Given the Novell IPX address 1aceb0b.0000.0c12.3456 which
part is
the network portion of the address?
A.) 0000
B.) 1
C.) 3456
D.) 1ace
E.) 0000.0c12.3456
F.) 1aceb0b | | 2 |
| what is frame relay? | | 8 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
