| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which device works at the Network Layer of the OSI model?
Router
Switch
Bridge
Hub
| | 3 |
| Identify IPX SAP and it's purpose?
A.) Sonet Access Pipe - interface to Sonet ring
B.) Service Advertising Protocol - advertise services
C.) Server Appletalk Protocol - appletalk directory services
D.) Service Access Point - identify upper layer protocols | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| Hi Guys i hv one confusion. Need u peoples help.
In EIGRP, maximum hop count is up to 255. By default only
100. Now question is -
a) Suppose i hv a network consist of 115 routers & EIGRP
routing protocol is configured. By default hop count is 100,
so is there any manual configuration necessary for hop count
ya router will automatically detect the hop count & will
update the hop count accordingly..?????
b) In EIGRP, Bandwidth & Delay is used to calculate metric.
For this Metric weight is set to K1(Bandwidth)=1,
K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0
Now i want, Bandwidth & Load is used to calculate metric.
For that wat i hv to configure & wat wub the metric weights.
Cud anyone explain it plzzzz..!!!! | | 5 |
| Which of the following describe full-duplex transmission?
A.) Uses a single wire
B.) Data transmission in both directions, but only one way
at a time
C.) Uses a point-to-point connection from the transmitter of the
transmitting station to the receiver of the receiving station
D.) Data transmission in only one direction | | 2 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| What does the term "attenuation" mean in data communication?
1 loss of signal strength as distance increases
2 time for a signal to reach its destination
3 leakage of signals from one cable pair to another
4 strengthening of a signal by a networking device
| | 1 |
| Which command specifies a second subinterface on serial
interface 0?
A. interface s 0.2 point-to-point
B. interface 2 s.0 point-to-point
C. suberinterface 2.s 0 point-to-point
D. interface s 0 sub 2 point-to-point
E. interface s 0.1 point-to-point sub 2 | | 1 |
| When using access lists, it is important where those access
lists
are placed. Which statement best describes access list
placement?
A. Put standard access lists as near the destination as
possible. Put
extended access lists as close to the source as possible.
B. Put extended access lists as near the destination as
possible. Put
standard access lists as close to the source as possible.
C. It isn't import where access lists are placed since the
router will
read and cache the whole list.
D. Put access lists as close to corporate headquarters as
possible. | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| Which router component stores routing tables APP cache and
packet buffers?
A. ROM
B. RAM
C. AVRAM
D. Flash memory | | 2 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make forwarding decision using MAC address
E.) Create collision domains | | 1 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| How do you get help on a command after you have received the
% incomplete command response from a switch CLI?
A. type "history" to review the prompt before the error
B. enter a question mark to display all the console commands
C. type help followed by the command to see command parameters
D. reenter the command followed by a question mark to view
keywords | | 1 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 2 |
| Which type of LAN segmentation device enables high speed
data exchange?
A. hub
B. bridge
C. switch
D. repeater | TCS | 2 |
| Which of the following use PVCs at layer 2?
A.) X.25
B.) HDLC
C.) Frame relay
D.) ISDN | | 1 |
| Identify 3 features of IGRP?
A.) Composite metric
B.) New horizon
C.) Flash (triggered) updates
D.) 60-second periodic updates
E.) Poison reverse | | 1 |
| Which OSI layer end to end communication, segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home.
D. a standard 28.8 analog dialup connection to the user at home. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
