| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What would be the first command from global configuration
mode to
enable
RIP on your router for interface E0, with an address of
181.86.4.4 and
mask of 255.255.255.0 ?
A.) router rip
B.) network 181.89.4.0 255.255.255.0
C.) router rip int e0
D.) router rip 181.86.0.0
E.) router rip 181.86.4.0
F.) network 181.86.0.0 | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Identify the hardware component that stores the backup
configuration?
A.) RAM
B.) NVRAM
C.) Flash
D.) ROM | | 1 |
| You can access three forms of WAN services with Cisco routers.
Select the three forms:
A. Switched or relayed services
B. Interface front end to IBM enterprise data center computers
C. Using protocols that connect peer-to-peer devices like
HDLC or PPP
encapsulation.
D. IPX/SPX
E. NetBEUI | | 1 |
| What are hold-downs used for?
A.) To prevent regular update messages from reinstating a
route that has
come back up
B.) Information received on an interface cannot be sent back
out the same
interface
C.) To prevent regular update messages from reinstating a
route that has
gone down
D.) To hold the routing table from being sent to another router | | 1 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| How does the cut-through switching technique work?
A.) By using broadcast address as source addresses
B.) The switch waits only for the header to be received
before it checks
the destination address and starts forwarding the packets
C.) The LAN switch copies the entire frame into its onboard
buffers and
then looks up the destination address in its forwarding, or
switching,
table and determines the outgoing interface
D.) By using a Class I repeater in a collision domain | | 3 |
| Which command specifies a second subinterface on serial
interface 0?
A. interface s 0.2 point-to-point
B. interface 2 s.0 point-to-point
C. suberinterface 2.s 0 point-to-point
D. interface s 0 sub 2 point-to-point
E. interface s 0.1 point-to-point sub 2 | | 1 |
| What does the command “IP name-server 255.255.255.255″
accomplish?
a.It disables domain name lookup.
b.It sets the domain name lookup to be a local broadcast.
c.This is an illegal command.
d.The command is now defunct and has been replaced by “IP
server-name ip any”
| | 5 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future? | | 3 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make forwarding decision using MAC address
E.) Create collision domains | | 1 |
| What is the distance limitation for 100BaseT?
A. 607 ft
B. 25 Meters
C. 1,000 ft
D. 185 Meters | | 1 |
| Which command will enable debugging for IPX RIP updates?
A.) debug ipx
B.) debug ipx rip
C.) debug ipx rip activity
D.) debug rip
E.) debug ipx packets | | 1 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 2 |
| what is telnet,ssh??
what is the perpose of this?
wer r this configured and how to configured?? | | 2 |
| Which of the following is not a characteristic of link-state
routing protocols?
❍ A. VLSM support
❍ B. Route summarization at any bit level
❍ C. Full routing updates at regular intervals
❍ D. Discontiguous network support | | 1 |
| If configuring a Cisco router to connect to a non-Cisco router
across a Frame Relay network, which encapsulation type would
you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | Cisco | 2 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
