| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which protocol carries messages such as destination
Unreachable, Time Exceeded, Parameter Problem, Source
Quench, Redirect, Echo, Echo Reply, Timestamp, Information
Request, Information Reply, Address Request, and Address
Reply?
A. ICMP
B. UDP
C. TCP
D. TFTP
E. FTP | | 2 |
| what is vc,pvc,lmi and dlsi | | 1 |
| what is standard and extended acess list?
what are the commands for extended and acess list? | HCL | 3 |
| HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS
PREFERED OVER ANY NETWORK PROTOCOL? | Aricent | 2 |
| Which of the following are Presentation Layer standards?
A.) JPEG and PICT
B.) MPEG and MIDI
C.) ASCII and EBCDIC
D.) NFS and SQL | | 2 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Router# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Which OSI layer incorporates the MAC address and the LLC?
A.) Data link
B.) Network
C.) Physcial
D.) Transport | | 1 |
| 9. Which STP state prevents the use of looped paths?
A. Blocking
B. Listening
C. Learning
D. Forwarding
| | 2 |
| Identify the definition of demarcation?
A.) Date in which the WAN service contract expires
B.) Cabling which extends from the WAN service provider to
the customer
C.) Division of responsibility, where the CPE ends and the
local loop
begins
D.) Equipment which is located at the customer premises | | 1 |
| What does the command “IP name-server 255.255.255.255″
accomplish?
a.It disables domain name lookup.
b.It sets the domain name lookup to be a local broadcast.
c.This is an illegal command.
d.The command is now defunct and has been replaced by “IP
server-name ip any”
| | 5 |
| You just entered the following command_Router(config#) line
console 0 Which operation is most likely to follow?
A. Confound terminal type
B. enter protocol parameters for a serial line
C. create a password on the console terminal line
D. establish a terminal type 4 connection to a remote host
E. change from configuration mode to console privileged mode | Wipro | 10 |
| Which two steps are required to confound and apply standard
access lists on an interface? (Choose two)
A. define an access list number and its parameters
B. enable an interface to become part of the access list group
C. define the number of access lists to be supported on an
interface
D. copy the access list definition to each interface that
will support it | | 2 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | | 1 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay | | 1 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| What command would you use to find out the names of Novell
servers on a network?
A. show ipx servers
B. show ipx hosts
C. show ipx sap
D. show ipx nodes. | | 1 |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | | 3 |
| Which layer allows multiple Ethernet devices to uniquely
identify
one another on the Datalink layer?
A.) Transport
B.) Session
C.) Network
D.) Datalink - MAC Sublayer
E.) Datalink - LLC Sublayer | | 3 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol?
| IBM | 15 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
