| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | | 1 |
| How signalling can be explained in D channel of ISDN? | Tulip | 1 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 4 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay | | 1 |
| Which of the following are examples of ICMP?
A.) Traceroute
B.) Web Browsing
C.) Ping
D.) Telnet
E.) Destination Unreachable message from a router
F.) Inverse Tunnels | | 1 |
| Which OSI Reference Layer controls application to application
communication?
A.) Datalink
B.) Network
C.) Transport
D.) Session
E.) Physical | | 1 |
| Which Cisco IOS command should you use to display the Novell
IPX address assignments on a router?
A. show ipx addresses
B. show ipx interface
C. show me the money
D. ipx, network (number)
E. display ipx addresses
F. show ipx routing details | | 1 |
| Identify 2 functions of IPX access-lists?
A.) Control SAP traffic
B.) Limit number of Novell servers on a network
C.) Limit number of workstations on a network
D.) Block IPX traffic | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| 6. Which device can create smaller networks and stop
broadcast storms by default?
A. Repeater
B. Bridge
C. Router
D. Gateway
| | 4 |
| What is true about frame-relay DLCI?
A.) DLCI represents a single physical circuit
B.) DLCI is optional in all frame-relay networks
C.) DLCI identifies a logical connection between DTE devices
D.) DLCI is used to tag the beginning of a frame with VLAN
information | | 1 |
| As system administrator, you type "debug ipx sap" and
receive the following lines as part of the IOS response:
type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops
type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops
What does "0x4" signify?
A. That is a Get Nearest Server response.
B. That it is a General query.
C. That it is a General response.
D. That it is a Get Nearest Server request. | | 1 |
| let threr are three router 1 is cionected to two and two is
conected to three
that is
1----2----3
now we can ping 2 from 3 and 1 to two but we are not able
to ping 1 to 3 let router 1 is local and rest of two are
remote what should be urs troubleshoot steps
| Volvo | 2 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Which of the following protocols are used to get an IP
address from a
known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 2 |
| What ISDN protocol specifies concepts, terminology, and
services?
A.) Q
B.) S
C.) I
D.) E | | 1 |
| |
| For more CCNA Interview Questions Click Here |