| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following is an example of the Physical Layer?
A.) SQL
B.) IP
C.) LLC
D.) DDP
E.) Ethernet | | 1 |
| Which of the following are examples of the Application Layer?
A.) LLC
B.) Token Ring
C.) Spreadsheet
D.) TCP
E.) IP
F.) Word Processor | | 1 |
| Which command displays the intenances using a given access list?
A. show filters
B. show ip interface
C. show active lists
D. show interface paramaters
E. configure ip access lists
F. show access-list interfaces | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 1 |
| In order to configure a Frame Relay subinterface with IP
identify
the 2 commands that must be configured on the physcial
interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay | | 2 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make fowarding decision using MAC address
E.) Create collision domains | | 1 |
| What would be the first command from global configuration
mode to
enable
RIP on your router for interface E0, with an address of
181.86.4.4 and
mask of 255.255.255.0 ?
A.) router rip
B.) network 181.89.4.0 255.255.255.0
C.) router rip int e0
D.) router rip 181.86.0.0
E.) router rip 181.86.4.0
F.) network 181.86.0.0 | | 1 |
| 2. What are the valid ways to segment a LAN? (Choose all
that apply)
A. Repeater
B. Bridge
C. Switch
D. Router
| | 2 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE cables. To which router would you add the clockrate
command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | TCS | 3 |
| there is three mode of vtp let there are three switch s1 in
server mode s2 in transparent mede and s3 in clint mode
then will that tranparnt mode going to effect the network if
yes then how and if no then what it will do | IBM | 1 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 2 |
| Identify the 2 commands to copy a configuration from a TFTP
server
to RAM?
A.) configure network
B.) configure overwrite
C.) copy backup-config running-config
D.) copy tftp running-config | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| Of the following switching types, which one has the lowest
latency?
A.) Cut-through
B.) Fragment Free
C.) None
D.) Store-and-forward | | 1 |
| what is the difference between osi and tcp ? | | 6 |
| What is VLSM? how to Calculate VLSM? where it is use and
why? | | 4 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| the term which used for describe physical alyout of network
mine answer-topology | | 1 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| Identify 3 methods used to prevent routing loops?
A.) Split horizon
B.) Holddown timers
C.) Poison reverse
D.) SPF algorithm
E.) LSP's | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
