| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| What three occurrences will reset the holddown timer after a
triggered
update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| Extended IP access-lists (100-199) can be used to control
traffic.
Which command listed below will permit smtp mail to only
host 3.4.5.6 ?
A.) It is not possible for SMTP traffic
B.) access-list 102 permit tcp any host 3.4.5.6 eq smtp
C.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 23
D.) access-list 102 permit tcp any any eq smtp
E.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 25 | | 1 |
| what is used for passive intercae comand
mine answer-to prevent to take update from outside | | 1 |
| Identify the switching method that examines the destination MAC
address as the frame is being received then begins
forwarding the frame
prior to receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| Hi Gyes
There are any sites where we can practice online for ccna
exams?Plz let me know because i get time to study in my
working hours only | | 1 |
| A router on one side of a PPP link uses the resonance RTR1
and the password COPP1-PWD. Which configuration line on
RTR1 enables a connection between RTR1 and another router
named RTR2?
A. username, RTR2 password COPR1-PWD,
B. username, RTR1 password COPR1-PWD,
C. username, RTR2 password COPR2-PWD,
D. username, RTR1 password COPR2-PWD, | | 1 |
| Which port numbers are used by TCP and UDP to set up
sessions with
other hosts?
A.) 1024 and above
B.) 6 and 17 respectively
C.) 1-25
D.) 6-17 | | 2 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 2 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| Identify the command mode necessary to enter the extended ping
command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)# | | 3 |
| Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router | | 1 |
| What is ISR or NonISR router? Difference between ISR or
NonISR router? | HCL | 3 |
| Which Distance Vector characteristic can help to speed up
convergence?
A.) Triggered Updates.
B.) Split Horizon.
C.) Poison Reverse.
D.) Hold Down timers.
E.) Inverse ARP. | | 1 |
| IGRP uses flash updates, poison reverse updates, holddown
times, and split horizon. How often does it broadcast its
routing table updates?
A. 90 seconds
B. 10 seconds
C. 30 seconds
D. 45 seconds | | 1 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 2 |
| When determining whether or not to route a LAN segment,
which rule
of thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| Which command assigns the login password CISCO on the
console terminal line?
A. line vty 0 login password cisco
B. line console login password cisco
C. line login terminal password cisco
D. line console 0 login
E. line console 0 login password cisco | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
