ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
tip   SiteMap shows list of All Categories in this site.
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
Identify the protocol to test connectivity without
configuring any

layer 3

protocols?

A.) TCP

B.) Ping

C.) IP

D.) CDP

E.) Telnet
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: Identify the protocol to test connectivity without configuring any layer 3 protocols? A.) TCP B.) Ping C.) IP D.) CDP E.) Telnet
Answer
# 1
Answer: D
 
Is This Answer Correct ?    1 Yes 0 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
Identify the command to determine if an IP access-list is grouped on interface e0? A.) Router(config)# show ip interface e0 B.) Router> show ip interface e0 C.) Router# show interface e0 D.) Router# show ip interface e0  1
What is a disadvantage of using a connection oriented protocal such as TCP? A. Packet acknowledgement may add overhead B. packets are not tagged with sequence numbers C. Loss or duplication of data packets is more likely to occur D. The application layer must assume responsibility for correct searchers of the data packets  1
Identify the access-list range for an extended IP access-list? A.) 800 - 899 B.) 1 - 99 C.) 1000 - 1099 D.) 100 - 199  1
To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks? A. Each router builds its own SAP table and forwards that every 60 seconds. B. Each router assigns a service number and broadcasts that. C. SAPs aren't necessary with Cisco routers. D. Cisco routers filter out all SAPs.  1
Which command will display the IPX routing table? A.) show routes B.) show routes ipx C.) show routes protocol=ipx D.) show ipx E.) show ipx route  1
I want to configure a serial interface on a 7500 with a VIP card. What global config command would give me access to a serial interface on a 7500? A.) int 1/0/0 B.) int s 1/0/0 C.) int s 1/1 D.) int s0.1 E.) int s1  1
The PDU at the network layer is a ________ Packet Frame Segment Bit  3
Identify the purpose of the Trace command? A.) Explorer packet transmitting routing information B.) Test connectivity C.) Determine the path a packet is taking through the network D.) Transmits user data when buffers are full  1
What information is provided by the local management interface (LMI)? A.) LMI encapsulation type B.) The current DLCI values C.) The status of virtual circuits D.) The global or local significance of the DLCI values  1
Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End  1
What is Cisco's default encapsulation method on serial interfaces? A.) ANSI B.) Cisco C.) Q933a D.) HDLC  1
Which addresses are valid host addresses? A. 201.222.5.17 B. 201.222.5.18 C. 201.222.5.16 D. 201.222.5.19 E. 201.222.5.31  2
Classful routing protocols do not include subnet masks in their routing updates. Which of the following routing protocols are considered classful? A.) EIGRP B.) OSPF C.) TCP D.) IGRP E.) RIP F.) IP  2
What is the difference between TCP and UDP? A.) TCP is connection-oriented; UDP uses acknowledgements only B.) TCP is connection-oriented; UDP is connectionless C.) Both TCP and UDP are connection-oriented, but only TCP uses windowing D.) TCP and UDP both have sequencing, but UDP is connectionless  4
Which of the following protocols are used for logical network addressing? A.) IP B.) TCP C.) ARP D.) ICMP E.) RARP F.) BootP  1
Extended IP access-lists (100-199) can be used to control traffic. Which command listed below will permit smtp mail to only host 3.4.5.6 ? A.) It is not possible for SMTP traffic B.) access-list 102 permit tcp any host 3.4.5.6 eq smtp C.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 23 D.) access-list 102 permit tcp any any eq smtp E.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 25  1
Which addresses are INCORRECTLY paired with their class? A. 240 - 255, Class D B. 240 - 255, Class E C. 224 - 239, Class D D. 224 - 239, Class E  2
Which layer is responsible for determining if sufficient resources for the intended communication exists? A.) Application B.) Network C.) Session D.) Presentation E.) Transport  2
Given the configuration example<HR> <B>interface ethernet0 ipx network 4a ipx access group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network 5c access list 800 permit 3d 4a</B><HR> Which two actions result from implementing this configuration? (Choose two) A. IPX network 5c will not receive any traffic B. Traffic from network 3d for network 4a will be forwarded out e0 C. Traffic from network 4a for network 3d will be forwarded out e0 D. Traffic from network 3d destined for network 4a will be forwarded out e2 E. The access list is applied to an outgoing interface and filters outbound traffic  1
Identify 3 LAN technologies? A.) FDDI B.) HDLC C.) HSSI D.) X.25 E.) 802.3 F.) 802.5  1
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com