| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does -1 signify in an extended IPX access list?
A. permit this host
B. deny this host
C. permit only this subnet
D. any host or any network | | 2 |
| Identify the hardware component used to store buffers, tables,
running-configuration etc?
A.) NVRAM
B.) ROM
C.) RAM
D.) Flash | | 3 |
| what is the diffination of bandwidth. | | 1 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| Identify the command to configure the router for IGRP autonomous
system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp | | 3 |
| Which of the following is an invalid host address using a
netmask
of 255.255.255.192?
A.) 10.1.1.1
B.) 10.1.1.66
C.) 10.1.1.130
D.) 10.1.1.127 | | 2 |
| Identify IPX GNS and it's purpose?
A.) Go Network Server - sends a print job to a network server
B.) Get Nearest Server - locate the nearest server
C.) Guaranteed Network Services - allocates resources to users
D.) Get Notes Server - locates Domino Server | | 1 |
| what hapeen we we configure default root on the router
which is conected by isp
supoese there are two router r1 is conected throug isp and
and by s0 r1 is conexted to r2
if we apply degault root on r1 what will happen | | 3 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| Which command can verify Application Layer connectivity
between 2
hosts?
A.) ftp
B.) snmp
C.) telnet
D.) ping
E.) traceroute | | 2 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to NVRAM before becoming enabled | | 1 |
| Which command will enable CHAP authentication on a serial
interface that is using PPP?
A.) encapsulation chap
B.) ppp chap
C.) ppp enable chap
D.) ppp encapsulation chap
E.) ppp authentication chap
F.) ppp chap enable | | 2 |
| Identify the command that displays ethernet0/1 interface status?
A.) show interface ethernet0/1
B.) show interface ethernet e0/1
C.) show interface ethernet0.1
D.) show ethernet0/1 | | 3 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| Which OSI layer defines end to end communication,
segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| What information is provided by the local management
interface (LMI)?
A.) LMI encapsulation type
B.) The current DLCI values
C.) The status of virtual circuits
D.) The global or local significance of the DLCI values | | 1 |
| Identify the purpose of ARP?
A.) Avoiding routing loops
B.) Determining a workstation's IP address
C.) Sending a directed broadcast
D.) Determining a workstation's MAC address | | 3 |
| Suppose we have 4 switches runing in VTP mode. So when i
create a VLAN in Server Switch this VLAN info reflect in all
other switch. So question is -
A) Suppose i m practicing this scenario in BOSON software,
When a create a VLAN in server switch n ADD ports of switch
to that VLAN, the same number of ports of client switch also
belongs to dat VLAN.
For example - In switch A (Server mode), i create a VLAN 7
name Hyderabad & port number 1, 2 & 3 put into this VLAN.
Another Switch B (Client mode), its also showing that port
number 1,2 & 3 belong the same VLAN.
How cud it possible... As we know, VTP share only VLAN
configuration information. Cud anyone explain it please....!!!!
B)Same thing, when i m practicing in PACKET TRACER 5.0, its
only showing that VLAN configuration information is shared.
No port information is shared at all. I can manually
configure individual switch port to respective VLAN as our wish.
Cud anyone explain it please..!!!
| | 3 |
| What is the Broadcast MAC Address? | Avaya | 2 |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
